background image

TOOL USE AND CARE

l

Read all the instructions and warnings first before attempting to operate this jack

.

l

DO NOT 

operate jack on inclined surfaces. Jack must be used on a level surface only. 

Unanticipated motion can occur as soon as jack lifts the tyre from surface.

l

DO NOT 

overload jack beyond the load rating (1500 lbs. per unit)

l

DO NOT 

start the vehicle’s engine, or drive a vehicle while the jack is in use. Jacks are designed 

for hand maneuvering of vehicles only. 

l

DO NOT 

use jack to lift tyres wider than 12 inches.

l

DO NOT 

attempt to push jack over obstacles. Jack is designed to be used on level and smooth 

surfaces only.

l

After lifting, be sure to always lock the pin in place before operating. 

Pull the pin out after 

finishing work and then release the valve.

l

Do not force the tool. 

Tools  do a better and safer job when used in the manner for which they 

are designed. Plan your work, and use the correct tool for the job.

l

Store idle tools. 

When tools are not is use, store them in a dry, secure place out of the reach of 

children. Inspect tools for good working condition prior to storage and before re-use.

l

Use only accessories that are recommended 

by the manufacturer for your model. 

Accessories that may be suitable for one tool may create a risk of injury when used on another 

tool.

l

Keep guards in place 

and in working order.

l

Never leave tool 

unattended. 

OPERATION

1.

Place jack on floor and press down on the pedal to release pedal lock. Pull out the lock pin 

from frame.

2.

Before operation,  open  the release valve  by  turning  the  hand-wheel  counterclockwise. Expand 

the  jack  with  the  hand-wheel  to  place  the  rollers  around  the  tyre;  position  the  jack  so  both 

rollers  are  in  contact  with  the  tyre  tread.  To  obtain  the  best  control  of  the  jack  while 

expanding  the  rollers  around  the  tyre,  place  your  left  hand  on  top  of  the  left  side  axle  and 

place  your  right  hand  at  the  center  of  the  pedal.  Close  the  release  valve  by  turning  the 

hand-wheel clockwise to a snug-tight position; jack may now be used.

3.

Install  jack  so  that  the  unit  is  parallel  to  the  sidewall  of  the  tyre  to  be  lifted.  Leave 

approximately  3/4"  of  clearance  between  tyre  and  jack. 

This  is  very  important

.  If  unit  is 

misaligned, the tyre may hit the axle of the jack and not the rollers; this may damage the jack 

and void the warranty.

4.

To  lift  tyre,  flip  the  directional  lever  up,  then  place  foot  on  pedal, depressing  the  pedal  with 

smooth, even strokes. Cycle pedal until tyre is lifted from surface one inch or less. After lifting, 

the  lower  the  tyre  is  to  the  ground  the  more  stable  jack  will  be. 

After  lifting,  be  sure  to 

always  lock  the  pin  in  place  before  operation. 

If  using  more  than  one  jack,  repeat 

Содержание C20-040







Отзывы: