Duratuf SG2525 Скачать руководство пользователя страница 16

 

 

 

 

Riverlea Group Ltd warrant that the cladding used in the manufacture of the Sentry shed will not rust within 20 years from the date 

of purchase. 

 

 

Any liability for product failure that may arise will be limited to repair or replacement of the defective product and will only apply for 

the benefit of the original purchaser. Riverlea Group Limited will not be liable for any consequential loss or damage, labour, or 

transport charges. 

 

 

This warranty is conditional on: 



Construction, installation and maintenance being carried out as specified in the Assembly Instruction Manual. 



The shed being installed in modest inland corrosion zones or areas where the steel corrosion rate is less than 200g/m2          

(as published by Branz). 



Warranty certificate being returned to manufacturer within 21 days of purchase together with proof of purchase.  

 

 

This warranty does not cover the following: 



Fastenings and fixings. 



Normal wear and tear, damage by impact or acts of God. 



Situations where the shed has been used for storage of chemicals, manure or corrosion causing products.

 



Unauthorized modification of the structure, including painting of the cladding.

 

 

Please visit http://www.riverleagroup.co.nz/warranty-garden-sheds to validate the Warranty on your shed. 

Click on the Warranty Registration Link and complete all details. 

 

If you are unable to access the computer, please phone us on 0800 438 274 and one of the customer services team 

will help you to activate the warranty on your garden shed.  

 

 

Many thanks, from the Team at Riverlea Group. 

20 YEAR WARRANTY

 

WARRANTY REGISTRATION

 

Содержание SG2525

















Отзывы: