background image

29

29

GUARANTEE TO CUSTOMER

Congratulations on purchasing a Duratuf Storage Shed. With proper care and attention, this product will last any years.

For your benefi t 

PLEASE READ THE FOLLOWING INFORMATION CAREFULLY.

WARRANTY ON METAL CLADDING

Riverlea Group Ltd guarantee that the metal roofi ng and wall cladding on Kiwi and Fortress Garden Sheds may be used in moderate and inland corrosion zones or areas where the fi rst year mild steel corrosion rate 

is less than 200g/m2, and that in these conditions, they will not perforate due to corrosion within 18 years of date of manufacture.

TERMS AND CONDITIONS

 

1.  Damage or corrosion due to the following circumstances is not covered by this warranty.

 

 

•   

Mechanical, chemical or other damage sustained during or after installation.

   

 

NOTE

: Clean swarf off  shed 

IMMEDIATELY

 after assembly

   

  Do 

NOT

 mark cladding with pencil

  

Do 

NOT

 allow manures, chemicals or other corrosive materials to have direct contact with cladding

  • 

Force majeure or other causes beyond the control of Riverlea Group Ltd.

 

2.  This warranty does not cover material installed in severe and very severe environmental situations, or in any area where the mild steel corrosion rate (as published by BRANZ) exceeds 200g/m2.

 

3.  Minimum maintenance must be carried out in accordance with instructions below.

Should the cladding fail to perform as specifi ed above, the liability of Riverlea Group Ltd shall in all cases be limited to replacing or repairing the defective product. The balance of the original warranty will cover any 

repaired or replaced material. Riverlea Group Ltd will not be liable for any consequential loss or damage, labour or transport charges. All claims made in writing within 21 days of discovery, quoting the reference 

number at the top right hand corner of this page.

MAINTENANCE

Following are the minimum maintenance requirements for cladding used in Kiwi Garden Sheds and Fortress Sheds.

 

• 

Washing all surfaces by rain, and annual hosing of sheltered areas using a hose and soft nylon brush.

 

• 

Within 2km of coast—wash every 3 months as above. After a storm, wash the cladding and the gutters as soon as possible to remove any highly corrosive salt deposits.

 

• 

Volcanic Ash Fallout—wash as soon as possible, removing fallout from roof and gutters.

 

• 

Gutters to be kept clean of leaves and dirt.

Should you require additional technical information please contact us at the details below.

Please visit http://www.riverleagroup.co.nz/warranty-garden-sheds to validate the Warranty on your shed.

Click on the Warranty Registration Link and complete all details.

If you are unable to access the computer, please phone us on 0800 438 274 and one of the customer services team will help you to acti-vate the warranty on your garden shed.

Many thanks, from the Team at Riverlea Group.

DURATUF PREMIUM SHED WARRANTY

WARRANTY REGISTRATION

Содержание Ponsonby






























Отзывы: