background image

13

13

CLADDING DETAIL

Overlap

13

WALL CLADDING - BACK & ENDS

•  Note - When attaching wall cladding always ensure top sheet is level with top 

plate and ends of sheet are fl ush and parallel with studs. This will ensure that 

wall panels are square. (Always screw wall sheets through the trough of the 

profi le)

•  Position 1st sheet fl ush with top of top plate and both ends of sheet are fl ush 

with outside of studs.

•  Using a 25mm tek screw, screw one end of sheet to frame. (Note - screw 

approx 25mm back from end of sheet. Corner fl ashing will cover screws when 

attached.)

•  Repeat at the other end, ensuring top of sheet is fl ush with top of top plate.

•  Screw sheet near the bottom, ensuring the ends of sheet are fl ush or parallel 

with stud.

  NOTE: The middle sheet will need to lap UNDER the top sheet, so don’t 

screw right at the bottom of the sheet yet! The top sheet will fi nish 

848mm below the top of the framing and the second sheet fi nishes 

1610mm down 

•  Position 2nd sheet underneath the fi rst sheet, repeat above. Make sure the 

above sheet is always overlapped correctly.

•  Using four 25mm tek screws, repeat above steps ensuring  sheet is level and 

fl ush at each end.

•  Position and screw bottom sheet using four 25mm tek screws.

•  Using 25mm tek screws in the middle of the sheet, screw the three wall sheets 

off  as per plan. (fi ve screws per end of each sheet and four in the middle).

•  Repeat above steps with each side wall.

WALL CLADDING - FRONT

•  Position and screw sheet above doorway ensuring sheet is fl ush with top of top 

plate and both ends of sheet are fl ush with outside of studs. (Use three 25mm 

tek screws in each end and three screws along top plate and one 25mm tek 

screw in each 320mm stud)

•  Fit remaining sheets each side of doorway and screw off  as above.

1610mm

848mm

Содержание Fendalton






























Отзывы: