background image

DURATUF PREMIUM SHED WARRANTY

 

GUARANTEE TO CUSTOMER

 

Congratulations on purchasing a Duratuf Storage Shed. With proper care and attention, this product will last many years.

 

For your benefit 

PLEASE READ THE FOLLOWING INFORMATION CAREFULLY.

 

 

 

WARRANTY ON METAL CLADDING

 

Riverlea Group Ltd guarantee that the metal roofing and wall cladding on Kiwi and Fortress Garden Sheds may be used in moderate and 

inland corrosion zones or areas where the first year mild steel corrosion rate is less than 200g/m2, and that in these conditions, they will 

not perforate due to corrosion within 30 years of date of manufacture.

 

 

 

TERMS AND CONDITIONS

 

1.

 

Damage or corrosion due to the following circumstances is not covered by this warranty.

 

 

Mechanical, chemical or other damage sustained during or after installation.

 

 

 

   

NOTE: 

Clean swarf off shed 

IMMEDIATELY

 after assembly

 

 

 

   Do 

NOT 

mark cladding with pencil

 

 

 

   Do 

NOT 

allow manures, chemicals or other corrosive materials to have direct contact with cladding

 

 

 

   Chemical damage will result if these instructions are not carried out

 

 

Force majeure or other causes beyond the control of Riverlea Group Ltd.

 

 

2.

 

This warranty does not cover material installed in severe and very severe environmental situations, or in any area where the mild 

steel corrosion rate (as published by BRANZ) exceeds 200g/m2.

 

3.

 

Minimum maintenance must be carried out in accordance with instructions below.

 

 

Should the cladding fail to perform as specified above, the liability of Riverlea Group Ltd shall in all cases be limited to replacing or      

repairing the defective product. The balance of the original warranty will cover any repaired or replaced material. Riverlea Group Ltd will 

not be liable for any consequential loss or damage, labour or transport charges. All claims made in writing within 21 days of discovery, 

quoting the reference number at the top right hand corner of this page.

 

 

 

 

MAINTENANCE

 

 

Following are the minimum maintenance requirements for cladding used in Kiwi Garden Sheds and Fortress Sheds. 

 

 

Washing all surfaces by rain, and annual hosing of sheltered areas using a hose and soft nylon brush.

 

 

Within 2km of coast—wash every 3 months as above. After a storm, wash the cladding and the gutters as soon as possible 
to remove any highly corrosive salt deposits.

 

 

Volcanic Ash Fallout—wash as soon as possible, removing fallout from roof and gutters

 

 

Gutters to be kept clean of leaves and dirt.

 

 

Should you require additional technical information please contact us at the details below.

 

Please visit http://www.riverleagroup.co.nz/warranty

-

garden

-

sheds to validate the Warranty on your shed.

 

Click on the Warranty Registration Link and complete all details.

 

If you are unable to access the computer, please phone us on 0800 438 274 and one of the customer services team will help you to acti-
vate the warranty on your garden shed.

 

 

Many thanks, from the Team at Riverlea Group.

 

WARRANTY REGISTRATION

 

Содержание SHEDS MK4A

















Отзывы: