Duratrax Raze ST Скачать руководство пользователя страница 3

3

THINGS TO

KNOW

SAFETY PRECAUTIONS

When the safety precautions are followed, 
the Raze ST will provide years of enjoyment. 
Use care and good sense at all times when 
operating this radio controlled truck. Failure 
to use this vehicle in a safe, sensible manner 
can result in injury or damage to property. 
You and you alone must insure that the 
instructions are carefully followed and all 
safety precautions are obeyed.

•  Do not operate the Raze ST near people. 

Spectators should be behind the driver or 
at a safe distance away from the vehicle.

•  Water can cause the electronics to short 

out and can cause permanent damage.

•  Always turn on the transmitter before 

turning on the receiver.

•  Fully extend the transmitter antenna before 

operating your vehicle.

•  Before turning on your radio system, check 

to make sure that no one else is running 
on the same frequency.

•  The engine and exhaust produce quite a 

bit of noise. Do not run this vehicle when 
or where it can disturb others.

•  The engine and exhaust can become very 

hot. Avoid touching any of these parts during 
use and until they have cooled down.

•  Model engine fuel is poisonous. Make sure 

you read and follow all of the precautions 
on the fuel container. Keep fuel out of the 
reach of children.

•  Model engine fuel is fl ammable and when 

ignited has a fl ame that is diffi cult to see. 
Avoid sparks, fl ames, smoking, or any 
other ignition source when fuel is near.

•  The engine emits harmful fumes just like real 

vehicles. Do not operate this model indoors.

•  Avoid running the truck in cold weather. The 

plastic and metal parts can become brittle 
at low temperatures. In addition, grease 
and oil become thick, causing premature 
wear and poor performance.

SPECIFICATION AND

DESCRIPTION CHANGES

All pictures, descriptions and specifi cations 
found in this instruction manual are 
subject to change without notice. DuraTrax 
maintains no responsibility for inadvertent 
errors in this manual. Visit www.duratrax.
com for the latest updates and information 
for your model.

WARRANTY

•  DuraTrax

®

 guarantees this kit to be 

free from defects in both material and 
workmanship at the date of purchase. 
DuraTrax will warranty this kit for 90 
days after the purchase date. DuraTrax 
will repair or replace, at no charge, the 
incorrectly made part.

•  Make sure you save the receipt or invoice 

you were given when you bought your 
model! It is your proof of purchase and 
we must see it before we can honor the 
warranty. Further, DuraTrax reserves the 
right to change or modify this warranty 
without notice.

•  In that DuraTrax has no control over the 

fi nal user assembly or material used for 
fi nal user assembly, no liability shall be 
assumed nor accepted for any damage 
resulting from the use by the user of the 
fi nal user-assembled product. By the act 
of using the user-assembled product, the 
user accepts all resulting liability.

To return your Raze ST for repairs covered 
under warranty you should send your truck to:

Hobby Services

3002 N. Apollo Drive Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am-5:00 pm 

Central Time M-F

E-mail: [email protected]

www.hobbyservices.com

If the buyer is not prepared to accept the 
liability associated with the use of this 
product, the buyer is advised to return 
this kit immediately in new and unused 
condition to the place of purchase.

STRESS-TECH

 PARTS

GUARANTEE

We have engineered the Raze ST to take 
the rough and tumble abuse that makes 
R/C buggies fun. We are so confi dent  of 
the quality and durability of the Stress-Tech 
plastic parts that we will replace any Stress-
Tech plastic part you break during the fi rst 
12 months you own the truck. Just send in 
the part to us and we will send you a FREE 
replacement. Please see the Raze ST parts 
list for the items covered under the Stress-
Tech guarantee.

To receive your free replacement part 
please send the following to the Hobby 
Services address listed under the warranty 
on the left.

 1. The broken part must be included.

 2.  The part number and description of the 

broken part.

 3.  Copy of your dated invoice or 

purchase receipt.

 4.  Your name, phone number and 

shipping address.

REPAIR SERVICE

Repair service is available anytime.

•  After the 90 day warranty, you can still have 

your Raze ST repaired for a small charge 
by the experts at DuraTrax’s authorized 
repair facility, Hobby Services.

•  To speed up the repair process, please 

follow the instructions listed below.

 1.  Under most circumstances return the 

ENTIRE vehicle. The exception would 
be sending in a Stress-Tech part. See 
the instruction under the Stress-Tech 
Guarantee.

 2.  Make sure the transmitter is turned off, 

all of the batteries are removed and 
the fuel tank is completely empty.

 3.  Send written instructions which include: a 

list of all items returned, a THOROUGH 
explanation of the problem, the service 
needed and your phone number during 
the day. If you expect the repair to be 
covered under warranty, be sure to 
include a proof of date of purchase (your 
store receipt or purchase invoice).

Содержание Raze ST





















Отзывы: