background image

 

 

Instruction Manual 

DHS-05 & DHS-1 Spreader - V1.4 

www.durapac.com 

Page 6 of 10 

 

6.0

 

Maintenance 

 

IMPORTANT: 

 

 

Use only good quality hydraulic fluid. 

Do NOT

 use brake fluid, transmission fluid, 

turbine oil, motor oil, alcohol, glycerine etc. Use of anything other than good quality 
hydraulic oil will void warranty and damage the pump, hose, and application. We 
recommend Durapac Hydraulic Oil or equivalent 

 

 

Equipment must only be serviced by a qualified hydraulic technician. For repair service, 
contact your local Durapac authorised service centre 

 

 

Damage to hydraulic hoses may not be detected during visual inspections. For this 
reason, Durapac recommends that hydraulic hoses be replaced on a regular basis 

 

 

Tighten connections as needed. Use non-hardening pipe thread compound when 
servicing connections 

Dirt, sand, etc. will quickly ruin any hydraulic system.  Ensure that couplings are clean and 
free of foreign matter. After each use, clean couplings and attach dust caps. 

Maintenance is required when wear or leakage is noticed. Periodically inspect all 
components to detect any problem that may require service and maintenance.  

6.1

 

Check for loose connections and leaks 

6.2

 

Replace damaged parts immediately 

6.3

 

Do not exceed oil temperature above 60

o

C  

6.4

 

Keep all hydraulic components clean 

6.5

 

Use dust caps when spreader is disconnected from the hose. Keep clean to prolong the 
product’s life. 

6.6

 

Wipe thoroughly clean and store spreader upright (to prevent seal distortion) in clean, 
dry environment. Avoid temperature extremes. 

6.7

 

Change hydraulic oil in your system as recommended in the pump instruction sheet 

6.8

 

Periodically lubricate lifting wedge with a small amount of high quality grease. 

6.9

 

Periodically apply a coating of light lubricating oil to pivot points and hinges. 

 

Содержание DHS-05











Отзывы: