DURA NIGHT TUNDRA Скачать руководство пользователя страница 23

Страница: 23 / 28

TROUBLE SHOOTING:

1. The battery is not fully charged.

2. Elevator servo is reversed.

3. CG too far backwards.

1. Charge the battery.

2. Change servo direction via Tx.

3. Move battery forwards.

1. Transmitter/Receiver batteries

are flat.

Problem

Cause

Solution

Motor does

not turn

1. Batteries is not fully charged.
2. Transmitter battery low.
3. Motor not connected.

4. The motor is damaged.
5. Receiver is not bound to Tx.

6. ESC in set-up mode.

Control surfaces

not moving with

stick input

Model does not

fly straight

Model does not

climb well

Limited Radio

Range

1. Charge/replace batteries.

Model moves

backwards

1. Prop installed backwards

1. Swap the prop around.

1. Charge the batteries.
2. Install a charged battery.
3. Check for connection

between the ESC and motor.

4. Replace motor.
5. Consult Radio manual and

go through bind procedure
again.

6. Hold model and move

throttle to full position then
back down to idle.

1. The servo lead is connected

to Rx incorrectly.

2. The servo is damaged.

Make sure the servo leads

are connect

properly.

Replace servo.

1. Control surfaces not centered.

2. CoG is not in the correct position.

1. Adjust the trims on the

transmitter.

2. Re-position LiPo as

suggested.

Содержание NIGHT TUNDRA





























Результаты поиска

Содержание NIGHT TUNDRA

Отзывы:

Похожие инструкции для NIGHT TUNDRA

Бренды по названию

Популярные бренды

DURA NIGHT TUNDRA, Инструкция по эксплуатации

Результаты поиска

Содержание NIGHT TUNDRA

Отзывы:

Похожие инструкции для NIGHT TUNDRA

Бренды по названию

Популярные бренды