background image

Unit 5 Judge Court, North Bank, Berryhill Industrial Est. Droitwich, Worcestershire, England, UK, WR9-9AU

Telephone: 01905 797989 Fax: 01905 774296 email:[email protected]

2”BSP G621 with lockable

bypass

GS100 Single Zone
Gas Detector. 230V

AC  or 12 VDC

Supply.

SG500 Single Zone

Gas Sensor. IP30

SG580 EX Certified

Gas Sensor for

Natural Gas and

LPG.

Gas Solenoid Valves

from 1/2”BSP to 4”

Flanged EN161

approved.

GS150K Single Zone

Gas Detector . 230V

AC  or 12 VDC

Supply.

GS300 Three Zone

Gas Detector. 230V

AC  or 12 VDC

Supply.

SG590 Catalytic

Nat Gas or LPG

Gas Sensor. IP55.

 12 VDC Supply.

4-20mA output.

CO100 Catalytic

Carbon Monoxide

Gas Sensor. IP55.

12 VDC Supply.

4-20mA output.

CO200 and 230 Catalytic

Carbon Monoxide Gas

Sensor with digital display

and Change over Relay.

30ppm CO. IP55.

Product

Overview

Gas

Detection

CO200A CO Sensor

for Car Parks. 12 or

24VDC supply

4-20mA Output. IP55

Gas

Safestart

Guarantee

This device is guaranteed for a period of 12 months from the date of purchase.

Conditions. Substitution free of charge of any component recognized as being faulty from production. The

unit must be delivered to the resaler or directly to Duomo.

KS21 Keystart  Control Panel

The Duomo Gas Safestart is.

..

a weep bypass assembly which proves that there are no gas
taps open or serious leakages in gas pipe-work which relies
on manually operated gas valves as the only means of
isolation.

Fact:
Manual gas valves do get left on and will be operated by
unauthorised individuals.

for Kitchens and Laboratories

Содержание BX444









Отзывы: