Duluth Forge FDF400RT-ZC Series Скачать руководство пользователя страница 29

Страница: 29 / 32

www.factorybuysdirect.com

200372-01A

TROUBLESHOOTING

Problem

Possible Cause

Corrective Action

White powder residue

forming within burner

box or on adjacent walls

or furniture.

1. When heated, the vapors

from furniture polish, wax,

carpet cleaners, etc., turn

into white powder residue.

1. Turn heater off when using

furniture polish, wax, carpet

cleaner or similar products.

Heater produces un-

wanted odors.

1. Heater is burning vapors from

paint, hair spray, glues, etc.

See

IMPORTANT

statement,

page 26.

2. Gas leak. See

Warning State-

ment

at the top of page 26.

3 Low fuel supply.

1. Open a window to ventilate

room. Stop using odor caus-

ing products while heater is

running.

2. Locate and correct all leaks

(see

Checking Gas Connec-

tions

, page 16).

3. Refill supply tank (Propane/

LP models).

Heater shuts off in use

(ODS operates).

1. Not enough fresh air is avail-

able.

2. Low line pressure.

3. ODS/pilot is partially

clogged.

1. Open window and/or door for

ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see

Care

and Maintenance

, page 24).

Gas odor exists even

when control knob is in

OFF position.

1. Gas leak. See

Warning

Statement

at top of page 26.

2. Control valve is defective.

1. Locate and correct all leaks

(see

Checking Gas Connec-

tions

, page 16).

2. Contact customer service.

Moisture/condensation

noticed on windows.

1. Not enough combustion/

ventilation air.

1. Refer to

Air for Combus-

tion and Ventilation

require-

ments, page 7.

ACCESSORIES

To purchase these heating accessories please visit our website

www.factorybuysdirect.com

or give us a call at 1-855-607-6557.

EQUIPMENT SHUTOFF VALVE

For all models. Equipment shutoff valve with

1/8" NPT tap.

Existing Gas Line

Shutoff Valve

Flexible

Connector

Flare & Pipe

INSTALLATION KIT

Содержание FDF400RT-ZC Series

































Результаты поиска

Содержание FDF400RT-ZC Series

Отзывы:

Похожие инструкции для FDF400RT-ZC Series

Бренды по названию

Популярные бренды

Duluth Forge FDF400RT-ZC Series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание FDF400RT-ZC Series

Отзывы:

Похожие инструкции для FDF400RT-ZC Series

Бренды по названию

Популярные бренды