Dulas VC50SDD Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 46

background image

VC50SDD Installation &

Technician’s Manual

Page 36 of 46

Section 3. How to check that the compressor is working

The Secop compressor and compressor controllers are a well-established design and are very
robust.

Note: Terminology in this procedure refers to the diagram on the following page and also
section 25. VC50SDD Electrical Schematic

Before testing the compressor confirm that the PV array is working

– see Section 2.

To test the compressor and compressor controller it can be directly connected to the PV as
follows, be sure to have confirmed that the PV array is working first:

1.

Switch the PV isolator off (indicated by a “0”).

2. Remove the 5 screws that secure the rear ventilation grill and remove it taking care not to

strain the connecting wires. .

3. Make a note of the connections to connector J2 so that they can be reconnected correctly

after completing the test.

4. Disconnect connector J2. Remove the 2 PV cables. Switch the PV isolator on (indicated by

a “1”). Check the open circuit voltage and short circuit current of the PV array.

5. Temporarily connect the PV cables to the compressor cables and capacitor cables. The

circuit board has labels by the connector.

PV+ cable should be connected to +Comp cable and +Cap cable. These 3 cables
should be the same colour.
PV- cable should be connected to Comp - cable and Cap- cable. These 3 cables
should be the same colour.

6. Disconnect connector J4, make a short circuit between the 2 wires leading to the

compressor.

7. Switch the PV isolator on. Check that the compressor and condenser fan are running. After

running for a few minutes the condenser should start to get warm.

8. If the compressor runs and after ten minutes the condenser gets warm it can be assumed

the compressor, compressor controller and refrigeration circuit are working.

9. Switch off the PV at the isolating switch. Now replace the connections to their original

condition:

Remove the short on the J4 connector and reconnect it to the circuit board.

Reconnect the PV, capacitor, and fridge cables to the J2 connector and reconnect
to the circuit board.

10. If the PV array is working and the compressor is working go to the next section to test the

Dulas SDD controller.

«
...
34
35
36
37
38
...
»

Содержание VC50SDD















































Отзывы:

Нет отзывов

Похожие инструкции для VC50SDD

Бренд: True Страницы: 2

Бренд: Kuppersbusch Страницы: 56

Бренд: Omcan Страницы: 100

Бренд: Norcold Страницы: 26

COOL MATIC RPD/RPA

Бренд: Waeco Страницы: 23

Бренд: Dacor Страницы: 15

Бренд: GVA Страницы: 15

Бренд: Blomberg Страницы: 81

Бренд: U-Line Страницы: 14

HRF-450D 6 Series

Бренд: Haier Страницы: 34

HSQ04WNA - 01-00

Бренд: Haier Страницы: 12

HSP05WNC - 04-06

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 17

HSL04WNA - 06-04

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 72

GE Profile Arctica PSI23MGN

Бренд: GE Страницы: 5

GE Profile Arctica CustomStyle PSW23PSR

Бренд: GE Страницы: 3

GE Profile Arctica CustomStyle PSW26PSRSS

Бренд: GE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды