Dulas VC50SDD Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 46

background image

VC50SDD Installation &

Technician’s Manual

Page 14 of 46

9.

Preparing to Install

Before starting the installation please read through the complete installation manual. By taking the

time to follow these simple instructions the whole installation process will be much easier.

1)

Carefully unpack the system and check that all components are present, familiarise

yourself with them and make sure that everything has been identified. Ensure that you

have all tools required to complete the installation.

2)

Familiarise yourself with the Dulas Installation Record in Section 24 of this manual. This

provides a step-by-step guide to the installation process and also gives you a formal record

of the installation.

3)

Discuss and decide a position for the refrigerator, ensuring that it is out of direct sunlight

and in a well-ventilated, dry place. The cooler the room, the better the performance.

Note:

avoid locations where room temperature may fall below +5°C.

4)

Identify a safe position for the solar array, ensuring that it faces the correct direction and is

mounted at the correct tilt angle for the system location

. Ensure that the solar array is

not, and will not become, shaded in the future and that it is accessible for cleaning

and maintenance.

5)

Work out the best route for the solar array output cable and the earthing cable, ensuring

that there is sufficient length to reach the refrigerator and that our advice on lightning

protection is followed (see Section 13).

Each component should have a sensible, well thought out,

safe

location, allowing access for

routine maintenance.

«
...
12
13
14
15
16
...
»

Содержание VC50SDD















































Отзывы:

Нет отзывов

Похожие инструкции для VC50SDD

Бренд: V-ZUG Страницы: 20

Бренд: V-ZUG Страницы: 120

Бренд: Zanussi Страницы: 28

Бренд: Daema Страницы: 10

Бренд: Thermador Страницы: 28

Silhouette DFF1044BLS

Бренд: Danby Страницы: 20

ChefLine CHPZ2P

Бренд: CHEFOOK Страницы: 102

Бренд: Omega Страницы: 10

Бренд: Zanussi Electrolux Страницы: 16

WINE CAPTAIN 2175BEVC

Бренд: U-Line Страницы: 2

Бренд: Randell Страницы: 4

Бренд: Galanz Страницы: 26

Бренд: U-Line Страницы: 47

Бренд: Gaggenau Страницы: 23

Бренд: Gibson Страницы: 19

Refrigerated Champagne Cellar 3SWCCE

Бренд: Marvel Страницы: 10

Бренд: Parmco Страницы: 20

Бренд: Summit Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды