Arctic Rush
®
Models 145, 145RH and 816C
184674
19
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
6.
Insert the assembled beater into
the cylinder by placing the rear
blade on the bottom of the cylinder
and depressing the front blade and
spring. This will center the beater
shaft and allow alignment with the
drive shaft. Rotate the beater
assembly while pushing, until the
shank has engaged the drive shaft.
7.
Slide the beater toward you about
½ inch — this is necessary to align
and install the head properly.
8.
Assemble the spigot assembly
(figure 7-4) by first installing the O-
ring (3) in the groove inside the
spigot body (2) and lubricate.
9.
Now install the spigot plug (4) up
through the bottom of the spigot
body (2).
10. While holding on the bottom of the
spigot plug (4), install the spring
(5), place the cap (6) on the spigot
plug and turn to lock in place, and
handle (7) onto the top side of the
spigot plug (4).
11. Thread the plastic nut (8) on the
spigot plug (4) then screw the nut
down tight.
12. Install and lubricate the air relief
plug O-rings (11) then insert the
plug (10) into the head (1).
13. Lubricate the inside of the head
bushing (12), then insert into the
head.
14. Apply lubricant in four dots, equally
distanced, in the face recess around
the front of the freezing cylinder, and
then place the head quad ring (13)
against the lubricant.
NOTE:
If the head does not slide easily
into place, recheck engagement of
beater with the drive shaft and head
bushing.
15. Line the head up so that end of
beater is in line with the head bush-
ing hole. Slide the head over the
studs and press in place against the
quad ring.
Important:
DO NOT use excessive force when
tightening the hand knobs. Exces-
sive force will damage the head.
Tighten finger-tight only.
16. Install the four hand knobs (9) on the
studs until they contact the head.
Draw knobs up equally, tighten
lightly,
with finger pressure only.
7 Assembly–
continued
