Duke AHPO-18 Скачать руководство пользователя

Страница: 22 / 24

Service Manual for

AHPO / EPO Proofer Oven

CAUSE

No power to unit

Oven Power Switch not turned on

Proofer Power Switch not turned on

No power
No water in Humidity Pan

Humidity Control OFF or not set properly

Humidity Element not working

Defective Humidity Control
Humidity Control set too high

Defective Humidity Control
Oven Power Switch not in ON position

Oven Thermostat not set

Defective Oven Thermostat

Defective Oven Heat Element/s
Oven Door not closed

Debris in fan wheel causing it to stick

Defective Safety Switch

Defective Motor
Proofer Power Switch not turned on

Proofer Thermostat not set properly

Defective Proofer Thermostat

Defective Proofer Heat Element/s
Debris caught in fan blades

Defective fan motor
Light Circuit Breaker open

REMEDY

Check plug for proper connection.

If OK, check circuit breaker.
Turn Oven Power Switch on

Turn Proofer Power Switch on

Check Circuit Breaker
Fill Humidity Pan

Adjust Humidity Control until proper humidity is achieved

Replace Humidity Element

Replace Humidity Control
Adjust Humidity Control until proper humidity is achieved

Replace Humidity Control
Turn Oven Power Switch to ON position

Adjust Thermostat to proper setting

Replace Oven Thermostat

Replace Oven Heat Elements
Ensure Oven Door is properly closed

Turn power off and clean debris from fan. Turn power on

and check for proper operation.

Adjust or replace the Safety Switch as needed

Replace Motor
Turn Proofer Power Switch on

Adjust Thermostat to proper setting

Replace Proofer Thermostat

Replace Proofer Heat Element/s
Turn Proofer power off and clean fan. Turn power on and

check for proper operation.

Replace fan motor
Reset Circuit Breaker. If problem persists, replace light

bulbs with 10 watt bulbs.

SYMPTOM

Oven and Proofer not working

Oven/Proofer Lights not working

Proofer Humidity not working/insufficient

Proofer humidity too high

Oven does not heat

Oven Fan does not operate

Proofer does not heat

Proofer Circulating Fan not working

Proofer Lights not on

TROUBLESHOOTING

Содержание AHPO-18

























Результаты поиска

Содержание AHPO-18

Отзывы:

Похожие инструкции для AHPO-18

Бренды по названию

Популярные бренды

Duke AHPO-18, Руководство по обслуживанию

Результаты поиска

Содержание AHPO-18

Отзывы:

Похожие инструкции для AHPO-18

Бренды по названию

Популярные бренды