Spin Welder User’s Manual
Section 3 – Safety
Page 17
Page 16
Dukane Manual Part Number 403-547-03
Dukane Manual Part Number 403-547-03
If a fuse has blown, determine the cause and repair
the defect before replacing the fuse. Replace the
fuses only with fuses of the same type and rating.
Grounding
It is important for operator safety that the receptacle
grounding wire be installed properly and securely
attached to an effectively grounded rod. The func-
tion of the ground wire is to keep the Spin Welder
base and housing at earth potential. In the event of
a short circuit from one of the three AC phases to
the case, the fuse(s) will blow, protecting the equip-
ment and operator.
A grounding lug is also provided on the back of the
base (Item 19 in Figure 2-3). You should connect
a separate 14 AWG* ground wire to an effectively
grounded metal pipe. This will minimize any ex-
ternal electrical interference from leaking into the
spin welder control circuitry. This will not com-
promise the safety of the power ground.
* 14 AWG wire has a diameter of 1.63mm or 0.064”
Mechanical Safety
The Spin Welder is capable of developing substantial
torque and high rotational velocity. Keep your hands
and body away from the tool head during operation.
The spinning head is capable of inflicting serious
injury. Never attempt to retrieve a part from a spin-
ning tool head. Always wear safety glasses when
operating the spin welder. Be extremely careful not
to let long sleeves, necklaces or long hair become
entangled in the spin welder during operation.
Pneumatic Safety
In the United States, you will have to add a device
capable of isolating and locking out the compressed
air supply to comply with OSHA regulations. Al-
ways lockout the compressed air when performing
any maintenance or service on the Spin Welder.
WaRninG
If there is any question
about the effectiveness
of your electrical ground-
ing, have it checked by a
qualified electrician.
WaRninG
Never touch the tool
head while the Spin
Welder is operating. The
spinning head is capable
of inflicting cutting and
crushing injuries.
Содержание SVB031
