background image

Note : The DIP switch setting will be taken effect only when you re-power on the 

camera

 

Control Button Description

 

 

Source 

Select 

Source selection : computer VGA or 
camera  

 

 

Digital 

Zoom 

Zooming from 100% to 300% 

 

Image 

Type 

Photo , Text , Invert or Mono   

 

Flip 

Rotate the image 180 degrees 

 

Decrease 

Brightness 

Decrease picture brightness 

 

 

Increase 

Brightness 

Increase picture brightness 

Some Using Tips 

Tip 1: How to avoid the hot spot.   

Glassy paper will result serious reflection of environment light and the 
lamp. If the document paper is glassy, you can take measures to 
overcome this problem.   

Change the camera location to avoid the overhead light source. 

♦ 
♦ 
♦ 

♦ 
♦ 

♦ 
♦ 

♦ 

♦ 

Turn off the lamp. 

Put the diffuse film on the paper to prevent a direct reflection. 

                Tip 2: How to control the camera to get best picture 

Turn on the lamp to get more light for better S/N ratio. 

Select the proper image type setting to get the best quality. 

Photo: Color picture, such as photo, color catalog .. 
Text : Text rich document , such as report, text book   
Invert : Negative film   
Mono: Gray only picture. 

Adjust the focus ring to get sharpening picture. 

Put the document as flatten as possible. 

Tip3: How to avoid a shadow image on document 

Don’t place your camera just beneath the lamps. You can turn off the 
room’s light and turn on the lamp. 

Tip 4: How to avoid image flickering   

The image flickering is caused by fluorescent lamp with power AC 
frequency 60Hz/50Hz light flickering. Please check your power system 
frequency and set the DIP switch accordingly to remove the flickering 
problem.  

Note : The DIP switch setting will be taken effect only when you re-power on 

the camera 

 

5

Содержание DC80A











Отзывы: