background image

 

Installation 

 

FOLLOW  STRICTLY  AND  IN  PRECISE  ORDER  THE  FOLLOWING  INSTALLATION 
INSTRUCTIONS,  OTHERWISE  MAY  RESULT  AN  ACCIDENTAL  NEBULISATION  OF 
HARMFUL GAS 

 

INSTALLATION OPERATIONS MUST BE DONE WITHOUT SPRAY CANS 

 

1.

 

Unscrew the three screws of motor base (fig. 2) and remove it carefully: unplug the motor (

CN2

and end-line (

CN7

) connectors freeing the base, then set it aside (fig. 3). 

Unplug the 

CN1

 connector 

2.

 

Fix the main case on wall using it as template for holes (fig. 3) 
Peperosso must be fixed stably on a solid vertical wall, with appropriate dowels, in such a way that 
the spray jet is as much as possible in the direction of any intruders 
Peperosso can be installed ONLY in vertical position 
Installation height can vary between 1,5 and 3 m 

3.

 

Deactivate  the  control  panel  with  tamper  control  excluded,  set  the  battery  and  lock  it  with  the 
appropriate metal plate 

4.

 

Plug the end-line 

CN7

 and motor 

CN2

 connectors 

5.

 

Connect the battery 

ATTENTION!

  By  connecting  the  battery  the  motor  move  forward  the  plunger  (leave  it  go 

completely forward) 

6.

 

Screw the three screws of the motor base 

7.

 

Cable the 

CN1

 connector according to the functioning mode will be used (instantaneous or driven 

by 

IN3

, see schemes at page 11 of this manuals) 

Ensure  the  control  panel  provide  the following  commands  to  the  connector  (this  is  the  minimum 
configuration required for a secure behaviour of the system): 
 

n°  Terminal 

Predisposition 

GND 

GND 

+12V 

+ 12 V

 

T1 

Tamper line 

T2 

Tamper line 

IN1 

+ 12 V

 (BLOCK) 

IN2 

+ 12 V

 (NEBULISATION READY) 

IN3 

This connection depends on functioning mode will be used: 

 

connected  to  NC  output  of  local  detector  for  driven  mode  or  to 
remote surveillance interface 

 

connected to 

IN2

 for instantaneous mode 

+VS 

supply  +12  V

  for  NC  contact  and  powering  the  local  detector  / 

surveillance interface 

 

Содержание PEPEROSSO




















Отзывы: