Duerkopp Adler 4280-6 Скачать руководство пользователя страница 32

Страница: 32 / 35

5.3 Setting the electromagnet current

The time response of the current of electromag. has 2 phases:

- initial switching on (0,2 ÷ 0,5 s) - the maximum force

- maintaining (when keying)

It is necessary to set max. 40 % of keying (see instru-

ctions for use of the stopmotor). With a higher value

thereof and with a long period of the presser foot

in its lifted position there is a danger of electromagnet

overheating.

5.4 Aseembly of the top roller lifting

electromagnet

Caution! Danger of injury!

Switch off the main switch! Before starting the setting

operation, wait until the motor stops!

- Remove the rear guard (3).

- Using the screws (1), fasten the electromagnet (2) on the rear

guard (3) with the given orientation of the outlet cable (4).

- Mount the rear guard (3).

- Connect the outlet cable (see par.7).

- Set the pin of the electromaghet (see par. 5.2).

- Set the current of the electromagnet (see par.5.3).

6. Backtacking using electromagnet

6.1 Description

The position of the electromagnet with regard to the backtacking

lever must be set in such a way that it enables the maximum stitch

length when sewing in forward and in rearward sense. If this

position is not correct, the length of the stitch will be shortened in

one or the other feed direction.

6.2 Electromagnet height setting

Caution! Danger of injury!

Switch off the main switch! Before starting the setting

operation, wait until the motor stops!

- Set the maximum stitch length.

- Set the position of the electromagnet (2) against the midpoint

of the grooves (1) of the guard (3).

- Mount the guard (3) on the head (the bar must have a clearance

between the stop on the backtacking lever and the extreme top

position at least of 0,5 mm).

- The backtacking lever (4) is to be shifted into its bottom position

(the bar (5) is to be in contact with the backtacking lever (4) ).

6.3 Setting the position of push-buttons

Caution! Danger of injury!

Switch off the main switch! Before starting the

setting operation, wait until the motor stops!

- By loosening the screws (1), it is possible to set the height of

the push-button holder.

6.4 Change of the function of push-buttons

The Function of the push-buttons can be changed in accordance

with the possibilities given by the stopmotor (see instruction

for use of stopmotor).

Содержание 4280-6




































Результаты поиска

Содержание 4280-6

Отзывы:

Похожие инструкции для 4280-6

Бренды по названию

Популярные бренды

Duerkopp Adler 4280-6, Инструкция по эксплуатации

Результаты поиска

Содержание 4280-6

Отзывы:

Похожие инструкции для 4280-6

Бренды по названию

Популярные бренды