Duerkopp Adler 4280-6 Скачать руководство пользователя страница 27

Страница: 27 / 35

3.11.2 Replacing the indented belt

To observe: in machines with Mini-stop first remove the driving

toothed belt as instructed in par. 3.13.

When replacing the indented belt, the mutual position of the

pulleys (4 and 5) should be maintained.

Caution! Danger of injury!

Switch off the main switch! Before starting the setting

operation, wait until the motor stops!

- Remove the handwheel, the belt guard and the V-belt.

- Remove the retaining ring (1) and remove the backtacking

lever (2).

- Mark with a pencil the instantaneous position of the

indented pulleys against the machine head in any position.

- Remove the indented belt (3) from the bottom indented pulley

(4) first, and then remove the whole belt.

- Apply a new indented belt on the top indented pulley (5) first.

- Turn both indented pulleys in the formerly marked positions

and apply the indented belt on the indented pulley (4).

- Tension the belt and mount the dismantled components in

the inverse order.

3.12 V-belt, motor - head

3.12.1 Tensioning

Caution! Danger of injury!

Switch off the main switch! Before starting the setting

operation, wait until the motor stops!

The belt is correctly tensioned, when the opposite sides of the

belt approach one to another by up to 20 mm in applying the

force of 10 N. The belt is tensioned in turning respectively the

motor in its holder.

3.12.2 Replacing the V-Belt

Caution! Danger of injury!

Switch off the main switch! before starting the setting

operation, wait until the motor stops!

- Loosen the screw (1) of the positioner arrest (2) and tilt the

arrest.

- Unscrew the screws (3) of the handwheel.

- Unscrew the screws (4) of the belt guard and tilt the guard.

- Remove the belt guard of the motor and tilt the protections

against falling out the belt from the motor pulley.

- Replace the belt.

- Tension the belt (see par. 3.12.1).

3.13 Driving toothed belt

3.13.1 To exchange the driving toothed belt

Caution! Danger of injury!

Switch off the main switch! before starting the

setting operation, wait until the motor stops!

- Remove the machine head from the stand (uncouple the

motor cables, the machine head cable, the position sensor,

and screw off the wood screw and the screw from the hinges).

- Remove the belt guard (1).

- Replace the belt (2).

2 1 4

10 N

l - 20mm

Содержание 4280-6




































Результаты поиска

Содержание 4280-6

Отзывы:

Похожие инструкции для 4280-6

Бренды по названию

Популярные бренды

Duerkopp Adler 4280-6, Инструкция по эксплуатации

Результаты поиска

Содержание 4280-6

Отзывы:

Похожие инструкции для 4280-6

Бренды по названию

Популярные бренды