background image

13

ENGLISH 

L2000651 Installation guide for DucoBox Silent (Revision N | 13.07.2020)

3

Press ‘HIGH’ or ‘LOW’ to activate the configuration mode for 30 minutes�

Then close the cover firmly.

Which configuration mode should I choose?

Button

Air calibration using 'HIGH'

This method is standard and has the 

lowest consumption� Recommended 

in the majority of homes�

Air calibration using 'LOW'

This method offers a boost mode 

but may give rise to more noise 

and higher consumption�

Low mode (10%)

Low mode (14-33%)*

Medium mode (50%)

High mode (100%)

High mode (100%)

Boost mode (143-333%)*

The percentages in the table indicate what percentage of the flow rate configured will be extracted�

The configuration mode chosen does not affect the operation of the AUTO mode�

* In the ‘LOW’ configuration, the percentage in low mode and boost mode is dependent on the type of 

home (see section "06�D Setting type of home" on page 10) and limited to the maximum achievable 

ventilation system flow rate�

HIGH

LOW

4

Close the DucoBox cover� 

Ensure it forms an airtight seal with the DucoBox�

5

Select the duct with the highest flow rate and restriction�

6

Measure at the vent and adjust the DucoBox rpm until the desired flow rate is 

obtained� This can be done in two ways:

• Using the   (lower) and   (higher) buttons on a paired User controller or CO

2

/

Humidity Sensor*�

• Using the ‘DOWN’ and ‘UP’ buttons on the DucoBox� This requires the cover to 

be removed temporarily� Always close the cover after every measurement.

Pressing the buttons once is equal to 1% (= approximately 2 to 3 m3/h per press of the button depending 

on the restriction in the ducts)�

 / 

 / 

7

Now measure the other vents� The flow rate from these other vents must only be 

adjusted at the vents themselves.

8

Repeat steps 

6

 and 

7

 until the desired flow rate has been obtained at each vent�

9

Exit configuration mode� This can be done in two ways:

• Long-press ‘AUTO’ on a paired User controller or CO

2

/Humidity sensor* until 

the 4 LEDs light up white briefly and then turn yellow again�

• Press ‘ENTER’ in the DucoBox and then immediately close the cover on the 

DucoBox� If the cover was not closed, you can pull the plug out of the power 

socket for a few seconds after closing the cover in order to reboot the DucoBox�

The DucoBox will now perform a calibration by speeding up high� This may take up 

to 1�5 min� Calibration will be complete once the DucoBox slows down the ‘AUTO’ 

button LEDs on the User controllers / CO

2

/Humidity sensors* will turn white, as 

will the LED on the DucoBox�

ENTER

* Depending on the software version of the User controller / CO

2

/Humidity sensor�

Содержание DucoBox Silent 0000-4215

















Отзывы: