Ducati SPORT 1000 S Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 96

Ducati SPORT 1000 S Скачать руководство пользователя страница 86

E

USA

85

Gasoline is extremely flammable and is explosive under
certain conditions. Refuell in a well ventilated area with
the engine stopped. Do not smoke or allow open flames
or sparks when refuelling or servicing the fuel system.
Always close the fuel petcock when the engine is not
running to prevent flooding of the throttle body. Do not
overfill fuel tank (see instructions page 41).
Motorcycle exhaust contains poisonous carbon
monoxide gas. Do not inhale exhaust gases and never
run the engine in a closed garage or confined area.
Use only Ducati approved parts and accessories.
This motorcycle was not intended to be equipped with a
sidecar or to be used to tow any trailer or other vehicle.
Ducati does not manufacture sidecars or trailers and cannot
predict the effects of such accessories on handling or
stability, but can only warn that the effects will be adverse
and any damage to motorcycle components caused by
the use of such accessories will not be remedied under
warranty.

Warning

Do not ride the motorcycle with helmets attached to

the hook; the helmets could cause an accident by distracting
the operator or interfering with normal vehicle operation.

Protective apparel

Always wear a helmet. Most motorcycle accident fatalities
are due to head injuries.
For safety eye protection, gloves, and high top, sturdy boots
should also be worn.

The exhaust system becomes very hot during operation,
never touch the exhaust system. Wear clothing that fully
covers your legs. Do not wear loose clothing which could
catch on the control levers, footrests, wheels, or chain.
Any amount of alcohol will significantly interfere with your
ability to safely operate your motorcycle. Don’t drink and ride.

Vehicle identification number (VIN)

Every Ducati motorcycle is identified by two identification
numbers (see page 9). fig. A specifically shows the frame
identification numbers.

ZDM 1W A B P X B 0 0 0 0 0 0

Var

i

es-can be thru

9

or X (Check d

i

g

i

t)

DUCATI

TYPE OF
MOTORCYCLE

MODEL
YEAR

PLANT OF
MANUFACTURE

SE

Q

UENTIAL

NUMBER

{

{

{

fig. A

«
...
84
85
86
87
88
...
»

Содержание SPORT 1000 S

































































































Отзывы:

Нет отзывов