background image

13.  Loncin powered Evolution3 Pressure Washer 

Maintenance Schedule

Activity

Each/ 

First Use

3 months  or 

first 50 Hours

12 months or 

250 hours

Inspect / top up oil levels            

 Engine 

*

 

Gearbox    

*        

 Pump

*

Change Oil           

 

Gearbox (SAE90 Gear Oil)           

*

*

 

Pump (SAE20/30 Pump Oil)

*

*

Change Engine Oil           

Refer to Engine Manufacturer's handbook

Water Suction Filter 

Clean water inlet filter on suction hose
Clean secondary water filter

*

*

Check Air Filter

Refer to Engine Manufacturer's handbook

Inspect high-pressure hose and its connection 
for tightness and damage

*

Inspect suction hose and its connections for 
tightness and damage

*

High Pressure Jet   

          

 

Inspect             

*

 Change

*

Pneumatic tyres
Check/Inflate tyre pressures (2.0bar, 30psi)

*
*

Check & Change Fuel Filter

Refer to Engine Manufacturer's handbook

Battery Charging Information

Risk of injury! Comply with safety regulations on the handling of batteries. 
Observe the directions provided by the manufacturer of the charger.

 

• Disconnect battery.

 

•  Connect positive terminal cable from the charger to the positive pole 

connection on the battery.

 

•  Connect negative terminal cable from the charger to the negative pole 

connection on the battery.

 

•   Plug in mains connector and switch on charger.

 

• Charge battery using lowest possible level of charging current.

!

15

Содержание Evolution E3T15400PLE





















Отзывы: