DTS TDAS WET Скачать руководство пользователя страница 6

TDAS WET User’s Manual 

April 2012 

 
 

 
 

[email protected]

 

6

 

Rev. 4 

COM A and COM B 

These  LED  indicators  are  green,  blinking  or  off.    A  green  LED  indicates  a  good 
communication  link.    The  LED  blinks  when  data  is  transmitted.    If  the  LED  is  off,  no 

link has been established for that COM port and troubleshooting is required. 

POWER 

This  LED  indicator  is  green  or  off.    A  green  LED  indicates  input  power  is  within 

specifications and the unit has been powered-up.  If you have input power connected 
to the unit and the POWER LED is not on, this can mean: 

1.

 

You need to press the push-button switch to power-up the unit, 

2.

 

Input power is not within specifications, 

3.

 

Input polarity is not correct. 

Additional troubleshooting can further isolate the problem. 

External Antennas 

Two  antennas  are  provided  with  the  TDAS  WET.    Both  antennas  are  required  for 
802.11n communications. 

Basic Care and Handling 

Your TDAS WET unit is designed to operate reliably in dynamic testing environments.  

Though  resistant  to  many  environmental  conditions,  care  should  be  taken  not  to 
subject  the  unit  to  harsh  chemicals,  submerge  it  in  water,  or  drop  it  onto  any  hard 

surface. 

WARNING: 

Electronic  equipment  dropped  from  desk  height  onto  a  solid 
floor  may  experience  as  much  as  10,000 g.    Under  these 
conditions, damage to the exterior and/or interior of the unit is 
likely. 

When  transporting  the  unit,  treat  it  as  you  might  a  laptop  computer  and  you  should 

have  no  problems.    When  not  in  use  or  if  shipping  is  required,  we  suggest  that  you 
always place the unit in the padded carrying case originally provided with your system. 

The TDAS WET is not user-serviceable and should be returned to the factory for service 

or repair. 

Shock Rating 

All crashworthy TDAS equipment is rated for 100 g, 12 msec duration, in all axes and 
can be mounted directly on a vehicle, sled or other dynamic testing device.  Mounting 

methods and mounting bolt selection should be carefully calculated so as to withstand 
expected  shock  loading.    (Please  see  Appendix  B  for  the  unit’s  mechanical 

specifications.) 

Содержание TDAS WET
















Отзывы: