THE WebDT 360
ENGLISH
4
5
ENGLISH
OPERATION
Internal Battery Switch
To prevent battery drain during shipping and extended storage, the internal
battery may be turned off. To turn on the internal battery, push the battery
button switch (on the back panel) to the “up” position (see page 2 for photo).
The internal battery pack has to be turned on for it to operate, be charged, and
for the optional external battery pack to function.
Powering ON and OFF
To activate the WebDT 360, push and quickly release the Power Button to the
left of the front bezel. The display will come on in a few seconds. To put the
WebDT 360 in Standby mode, push and quickly release the Power Button. To
turn the WebDT 360 off for extended storage, power off the device safely using
any software function that “shuts down computer” provided in the software
operating system.
NOTE:
The battery packs shipped with your device may be low in power—please
use the AC-DC adapter with the WebDT 360 when setting up the device for the
first time to fully charge the internal battery pack. You may charge the external
battery pack with it attached to the WebDT 360, or with the optional external
battery charger kit.
NOTE:
When the battery pack(s) is (are) charging, the blue-colored Battery LED
should blink slowly. If plugging in the AC-DC adapter does not trigger this blinking
activity and the LED stays dark, the battery pack(s) may have been drained
substantially. Try unplugging/replugging the AC-DC adapter to the WebDT 360
a few times to activate the charging process.
NOTE:
To conserve power, use (push and quick release) the Power Button to
put the device in “Standby” mode while not in use. Pushing briefly on the same
button will wake up the system within seconds.
NOTE:
Avoid using the Power Button (”hold 4+ seconds” feature) to turn off the
device—this form of hardware shutdown is intended to be a means of recovery
from device lockups, and not as normal operation.
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface
will be displayed after a launch sequence of several seconds. The wireless LAN
connection may take 10-15 seconds to be established.
Configuring the WebDT 360
The device may be configured using the utilities and methods dictated by
the software operating system. The WebDT 360 should be configurable for
various properties such as user profiles, network features, and several system
elements.
Calibration
The touch display for the WebDT 360 is calibrated before shipping. In the event
that the calibration has been modified or is unsatisfactory, the respective
calibration routines (e.g., PenMount (PM) for Windows XP) to calibrate the touch
interface may be used. Such applications are typically executed through touch
input via Stylus or through mouse click via a USB mouse.
NOTE: For Windows CE, calibration may be initiated from Stylus application in
the Control Panel or by simultaneously pressing Buttons 2 and 6.
WIRELESS NETWORKING
Wireless LAN
The WebDT 360 is often delivered with an embedded (user-inaccessible)
802.11a/b/g WLAN adapter equipped with a hidden custom antenna. This
embedded interface is supplemented by a user-accessible PCMCIA slot for use
with third-party network adapters or peripherals.
T
•
hrough the support of typical WLAN adapters, the WebDT 360 should be able
to detect all 802.11 access points in the vicinity for you to select the access
point of your choice for connection.
T
•
he SSID and WEP (if enabled) parameters on the WebDT 360 and the access
points have to match. The SSID is case-sensitive and it is recommended that
you enable WEP encryption (or advanced alternatives) for secure access.
W
•
hen WEP is enabled, you may need to consult your network administrator or
your networking equipment literature to properly configure associated settings
such as Authentication mode, etc.
R
•
efer to the access point operating manuals for setting up the 802.11 access
points.
