Document:
RE-BCC8FDM 1C7
Document:
RE-BCC8FDM 1C7
Document:
RE-BCC8FDM 1C7
Page:
3
Page:
3
OWNER'S MANUAL
RE-BCC8FDM camera license plate
DSE srl - Digital Surveillance Equipment - WWW.DSE.EU
IR illuminator and
choose how
1..6 operation
The button is available for occasional adjustments
in
As these same settings can be adjusted via the RS485 connection as we will see later.
Setting Mode
- By moving the button to the right and left will select the operating mode from 1
Setting Mode
- By moving the button to the right and left will select the operating mode from 1
(lenti- image lighter vehicles) to 6 (fastest vehicles, darker image).
Adjusting the IR LED power
- Using the up and down button increases and decreases the
Adjusting the IR LED power
- Using the up and down button increases and decreases the
brightness of the LEDs. Once the
level
desired you have to press the central button to store.
RS485 FOR REMOTE CONTROL
The camera is equipped with an RS485 port that should be used to remotely control the target,
there
brightness of the illuminators and the OSD menu.
Compared to the first versions of the product, where these adjustments is only then carried out on
the camera, the remote control makes it easy to intervene also installed camera.
To send RS485 commands it takes a PTZ console or DVR with RS485 port.
The settings to be set to communicate with the camera are fixed:
PROTOCOL PELCO D SPEED '9600
bps ADDRESS: 1 The commands
send to the camera calling the
following presets depending on the function you want to play.
CALL 101..106
- This command sets the operating modes 1 to 6.
CALL 101..106
- This command sets the operating modes 1 to 6.
CALL 200
- This command displays the current operating mode (1..6 number appears
CALL 200
- This command displays the current operating mode (1..6 number appears
superimposed)
MOVING UP / DOWN -
With the navigation commands up and down you change the brightness of
MOVING UP / DOWN -
With the navigation commands up and down you change the brightness of
MOVING UP / DOWN -
With the navigation commands up and down you change the brightness of
the IR LEDs. When you enter the preset 200 on the act
joystick
moving it up and down to change the power of the LEDs. Check the result on the monitor.
CALL + PRESET 201
- ends the adjustment With this command
CALL + PRESET 201
- ends the adjustment With this command
brightness of the LEDs and confirms
the setting.
CALL 97
- Changes the video output in CVBS, namely standard analog, for coupling
CALL 97
- Changes the video output in CVBS, namely standard analog, for coupling
with analog DVR that do not support the AHD The technology requires the switching time of 5
seconds.
CALL 98
- Switch the video output 1080P AHD (DVR requires that support AHD1080P
CALL 98
- Switch the video output 1080P AHD (DVR requires that support AHD1080P
technology). The recall of PRESET 95 does not open the OSD menu of the camera as not
technology). The recall of PRESET 95 does not open the OSD menu of the camera as not
accessible on these models.
PROBLEMS AND SOLUTIONS
Image B / W day
- If the illuminators are turned on, adjust IR activation threshold. If the picture is
Image B / W day
- If the illuminators are turned on, adjust IR activation threshold. If the picture is
B / N IR off IR filter is in the wrong position due to mechanical shock, Power up and power down
there
camera, then secure it more solidly.
IR LED does not light up at night
- Adjust the ignition threshold. Verify that there is a source of
IR LED does not light up at night
- Adjust the ignition threshold. Verify that there is a source of
light that illuminates the sensor on the rear of the camera.
Glare on the plate
- Avoid directly oriented towards the camera lights (min 30 °).
Glare on the plate
- Avoid directly oriented towards the camera lights (min 30 °).
The plate is moved
- Check goal setting. Reduce the shutter speed to 1/1000 or 1/1500
The plate is moved
- Check goal setting. Reduce the shutter speed to 1/1000 or 1/1500
Targa too bright or dark at night
- Adjust the power of the LEDs according to the shooting
Targa too bright or dark at night
- Adjust the power of the LEDs according to the shooting
distance
The power of LEDs varies after a reset
- Confirm the IR power settings to save it after
The power of LEDs varies after a reset
- Confirm the IR power settings to save it after
adjustment
The plate is too small and you can not read
- Increase the zoom lens to focus the shot.
The plate is too small and you can not read
- Increase the zoom lens to focus the shot.
No video
- Check setting AHD / CVBS according to your DVR.
No video
- Check setting AHD / CVBS according to your DVR.
TECHNICAL FEATURES
http://www.dseitalia.it/dati_telcavo.htm