Document:
RE-BCC8FDM 1C7
Document:
RE-BCC8FDM 1C7
Document:
RE-BCC8FDM 1C7
Page:
2
Page:
2
OWNER'S MANUAL
RE-BCC8FDM camera license plate
DSE srl - Digital Surveillance Equipment - WWW.DSE.EU
The camera is equipped with AHD 1080P in series mode unless otherwise requested in the
order.
pin DC12V -
We must connect a 12VDC power supply stabilized by at least 2,000 mA, such as
pin DC12V -
We must connect a 12VDC power supply stabilized by at least 2,000 mA, such as
pin DC12V -
We must connect a 12VDC power supply stabilized by at least 2,000 mA, such as
pin DC12V -
We must connect a 12VDC power supply stabilized by at least 2,000 mA, such as
RE-AL5 model (not included).
The requested plug is the standard 5.5 mm. Attention to use STABILIZED feeders that provide
12V in any load condition. The use of a different supply voltage from 12VDC can generate video
disorders and in the worst cases damage the camera. Beware extension power cables are too
long or
small section,
that could
to introduce
excessive fall
species voltage at the time
IR illuminator ignition.
RS485 input
- This connection allows you to connect an RS485 BUS which serves to remotely
RS485 input
- This connection allows you to connect an RS485 BUS which serves to remotely
control the target, the IR illumination power and other settings. To send the commands you can
use a PTZ console or our DVR that has RS485 port.
The two terminals of the RS485 port are connected with a twisted pair to the control mechanism,
respecting the order A + / B- without swap them.
To send commands using the following settings:
PROTOCOL PELCO P / D ADDRESS: 1
SPEED '9600
you can not change
TARGET
Adjust zoom / focus
- The camera mounts an adjustable objective lens from 5 to 50 mm ..
Adjust zoom / focus
- The camera mounts an adjustable objective lens from 5 to 50 mm ..
motorized that is controlled through the RS485 serial line.
Once the camera position is it is necessary to adjust the zoom and the focus of the lens by acting
on the organ of remote control via RS485
Acting initially on ZOOM (TW) and adjust the amplitude of the frame (wide angle / zoom) based
on the area to be framed. Remember that in most wide angle corresponds inevitably less image
detail. In general, it is good to frame a narrowest possible width around the location where it will
be located in the plate so that the same appears as large as possible in the frame.
Once you defined the field of view act on FOCUS adjustment to focus perfectly framed area.
Recall that each lens has its own depth of field to which it is possible to put in focus in a perfect
way only a portion of the space in front of the camera. Concentrate on the most important area
where you will find the plate of the vehicle to adjust the focus optimally.
It may be helpful for an optimal adjustment to position a car stops at the exact point where it
carries out the reading of the license plate.
IR LIGHT
The cameras integrates in its interior an infrared illuminator that emanates illumination invisible
to the human eye, but visible to the camera. The illuminator turns itself on when it gets dark and
the camera switches alone in night vision mode. The illuminator allows ignition
the vision of the license plate
absolute darkness until its flow rate of 30 meters illumination.
Note that in this camera, the illuminator is used for the vision of the automobile license plate and
does not allow, if not marginally, the night vision of the medium or environment.
If this
is
request must be
the tiling of another conventional camera.
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
IR threshold adjustment -
On the electronic circuit board inside the housing is placed a
potentiometer to adjust the illuminator ignition threshold. In most cases the adjustment is not
necessary. Intervening only if one realizes that the camera never switches to night mode or
switches in untimely manner due to abnormal conditions of ambient brightness.
The trimmer is placed in position factory 0. By screwing in a clockwise direction, towards the
position 1, the illuminator will turn on later. Unscrew anti-clockwise, to the position 4, it will be
activated soon. In the adjustment keep in mind that the camera reaction occurs with 5 seconds
delay to avoid that sudden flashes can make the camera move from night to day. It is therefore
necessary to turn a little potentiometer and wait for the reaction of the camera.
IR brightness adjustment
- E 'can adjust the brightness of the illuminator to adapt to the distance
IR brightness adjustment
- E 'can adjust the brightness of the illuminator to adapt to the distance
of the shot. If the plaque comes too close, within 10 m. for example, arrangement may reduce the
brightness to avoid that is too bleached. To properly adjust the lighting ask
in
real dark conditions and illuminators turned on by placing a retainer means in the license plate
reading point. If the license plate is bleached with unreadable characters must reduce the power
of the LEDs. Acting on the adjustment so as to optimize the illumination on the plate. The power
of the LEDs is adjusted with the button on the camera cable or remotely through the RS485 serial
port. The camera does not have indicators showing the power of the LEDs selected because this
is physically visible on the degree of power illuminator.
RULES 'OF OPERATION 1..6
These cameras for license plate reading does not allow the user to freely change the internal
settings of the video made to prevent inopportune modification may render ineffective the
camera. Factory 6 are arranged in the camera mode of operation (1..6) to be chosen according
to the speed of the vehicles.
Adjustments 1 to 4 are used for moderate speed. The 5 and 6 different settings are used for
high speeds and provide globally darker images as the shutter speed is higher.
The maximum speed of the means to take can not exceed 180 km / h. The mode setting of
operation
makes with the button on the camera cable or remotely via RS485
The camera shows overlay the number of the selected mode.
BUTTON ON BOARD ROOM
On the cable that protrudes from the camera is placed a mini-joystick that allows to modify
the power