Use the optional DM-W Wall Mount and DM-C Ceiling Mount
brackets to solve difficult placement
problems. The DM-W and DM-C
mount to either the wall or ceiling and
allow for full vertical and horizontal
positioning of the motion detector -
the detector can be tilted up or down
and rotated through 90° to obtain the
best position for optimal coverage.
The New Force 2 has been designed
to be fully compatible with the DM-W
and DM-C brackets. Contact your
DSC distributor for more information.
IMPORTANT NOTE: Maximum
detection coverage occurs when the
FORCE 2 is mounted at the height
specified in the mounting instructions and the mounting surface
is vertical. If this cannot be achieved with a mounting bracket,
then detector coverage may be less than specified.
WIRING
Once the detector is mounted in the desired location, connect the
wiring as shown below. Note that various models have the
following optional features.
FORCE 2 - OPTIONS
F2-210
F2-210
F2-210
F2-210
F2-210 ....................... ‘A’ Alarm contact only
F2-211
F2-211
F2-211
F2-211
F2-211 ....................... ‘A’ Alarm contact & Tamper switch
F2-212
F2-212
F2-212
F2-212
F2-212 ....................... ‘C’ Alarm contact & Tamper switch
NOTE: Contacts are shown in the non-alarm state with power
applied to the detector.
POWER
12V
DC
30mA
ALARM
Contacts Rated
100mA @ 24V
DC
TAMPER
Contacts Rated
100mA @ 24V
DC
OPTION
OPTION
NC
NO
10
Ω
GND +12
C
NC
NO
T1
T2
POWER UP
Upon application of power, the alarm indicator will be illuminated
for 60 seconds to indicate the unit is warming up. During this
period, the alarm relay is held in its normal non-alarm state. After
the 60 second warm-up period, the alarm indicator will go out and
the unit will respond to motion in the protected area.
ALARM INDICATOR ON/OFF JUMPER J1
With Jumper J1 OFF, the alarm indicator will turn on each time the
unit goes into alarm. With J1 ON, the alarm indicator is disabled.
WALK TESTING
It is imperative that the unit be thoroughly walk tested after mounting
to ensure that coverage extends over the desired area.
Once coverage has been confirmed, Jumper J1 may be set to the
ON position to disable the alarm LED indicator.
IMPORTANT NOTE:
Upon installation, the unit should be
thoroughly tested to verify proper operation. The end user should
be instructed on how to perform walk tests, and should perform a
walk test at least once per year.
DM-C
DM-C
DM-C
DM-C
DM-C
Ceiling Mounting Bracket
Ceiling Mounting Bracket
Ceiling Mounting Bracket
Ceiling Mounting Bracket
Ceiling Mounting Bracket
DM-W
DM-W
DM-W
DM-W
DM-W
Wall Mounting Bracket
Wall Mounting Bracket
Wall Mounting Bracket
Wall Mounting Bracket
Wall Mounting Bracket
TOP
PIR LENS
29002410 R002
COMPONENT LOCATIONS
J1
PIR LENS
The PIR lens is mounted with the textured
side facing in (smooth side facing out).
Note that the long lens elements are at the
top when the lens is properly positioned.
Ensure the lens is properly seated, and
that the lens holder is securely snapped
into place.
LIMITED WARRANTY
Digital Security Controls Ltd. warrants that for a period of five years
from the date of purchase, the product shall be free of defects in
materials and workmanship under normal use and that in fulfilment
of any breach of such warranty, Digital Security Controls Ltd. shall,
at its option, repair or replace the defective equipment upon return
of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in
shipping or handling, or damage due to causes beyond the control
of Digital Security Controls Ltd. such as lightning, excessive
voltage, mechanical shock, water damage, or damage arising out
of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and
is and shall be in lieu of any and all other warranties, whether
expressed or implied and of all other obligations or liabilities on the
part of Digital Security Controls Ltd. Digital Security Controls Ltd.
neither assumes, nor authorizes any other person purporting to act
on its behalf to modify or to change this warranty, nor to assume
for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any
direct, indirect or consequential damages, loss of anticipated
profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure
of this product.
WARNING: Digital Security Controls Ltd. recommends that the
entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product
to fail to perform as expected.
IMPORTANT INFORMATION
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL
SECURITY CONTROLS LTD. COULD VOID THE USER’S AUTHORITY TO OPERATE
SECURITY CONTROLS LTD. COULD VOID THE USER’S AUTHORITY TO OPERATE
SECURITY CONTROLS LTD. COULD VOID THE USER’S AUTHORITY TO OPERATE
SECURITY CONTROLS LTD. COULD VOID THE USER’S AUTHORITY TO OPERATE
SECURITY CONTROLS LTD. COULD VOID THE USER’S AUTHORITY TO OPERATE
THIS EQUIPMENT.
THIS EQUIPMENT.
THIS EQUIPMENT.
THIS EQUIPMENT.
THIS EQUIPMENT.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
UNDESIRED OPERATION.
UNDESIRED OPERATION.
UNDESIRED OPERATION.
UNDESIRED OPERATION.
is a trademark of Digital Security Controls Ltd.
© Digital Security Controls Ltd.
Toronto, Canada
Tech Line: 1-800-387-3630
Web Site: www.dscgrp.com
