Introduction
2
1.4 Approvals
1.4.1 Industry Approvals
• UL 1610 Central Station Burglar Alarm Units
• UL 864 Standard for Control Units and Accessories for Fire Alarm
Systems
• CAN/ULC-S304-06 Signal Receiving Centre and Premises Burglar
Alarm Control Units
• CAN/ULC-S559-04 Equipment for Fire Signal Receiving Centres
and Systems
• EN60950-1:2001 Standard for Information Technology Equip-
ment.
• AS/NZS 60950:2000 Information Technology Equipment - Safety
• CISPR22 Information Technology Equipment - Radio Disturbance
Characteristics - Limits and Methods of Measurements
• EN50130-4 Immunity requirements for components of fire,
intruder and social alarm systems.
This equipment shall be installed in accordance with the require-
ments of NFPA72, NFPA70, UL827 and the authority having juris-
diction.
SG-System III with SG-DRL3-IP Line Card is ULC listed for active
communication channel security level A4 when used in conjunction
with T-Link TL250 and T-Link TL300 Internet/Intranet alarm commu-
nicators. For this type of application the supervision and encryption
features have to be enabled.
For ULC Installations the equipment shall be installed in accordance
with the requirements of ULC-S561 and ULC-S301 Standards and
the authority having jurisdiction.
UL864 Programming Requirements
1.5 Receiver Setup and Operation
DSC recommends testing the receiver before actual installation.
Becoming familiar with the connections and setup of the unit on the
workbench will make final installation more straightforward. The
following items are required:
• IEC Power supply cord
• One network hub or router
• One or more dialer or digital control panel and a T-LINK TL250/
TL300
1.
Unpack the components for the System III.
NOTE:
Carefully unpack the receiver and inspect for shipping
damage. If there is any apparent damage, notify the carrier imme-
diately.
2.
Unscrew the front thumb screws and open the front
plates.
NOTE:
Before inserting the CPM3, connect the ribbon cable from
the UIB3 board. Before inserting the PSC3 connect the LCD back-
light.
3.
Insert all the cards in the rack, in their appropriate position.
Refer to Figure 1-2 in the System III Installation Manual.
Connect the ribbon cable of the front panel to the CPM3
before inserting it. Connect the backlight power connec-
tion to the PSC3 then insert the PSC3.
4.
Insert the PSU3 into the rack and fasten it properly.
5.
Connect an ethernet cable to the proper line card.
6.
Connect the main power (110V
AC
or 220V
AC
) using a
standard computer IEC cable (not supplied).
7.
The LCD will power up and display internal troubles
(printer, computer, telephone line fault, network absent).
The SG-DRL3-IP Receiver will have the green LED ON if the
ethernet line is connected. If the LED is not on, make sure
the ethernet line is connected to the right port
.
NOTE:
Internal diagnostics may require more than one minute
during the power up sequence.
8.
Send a signal from a control panel to the receiver. The sig-
nal will be displayed on the LCD. Press the [ACK] button to
silence the buzzer.
Table 1-1: UL864 Programming Requirements
NOTICE
to Users, Installers, Authorities having Jurisdiction, and other involved parties
This product incorporates field programmable software. In order for the product to comply with the requirements in the
Standard for Control Units and Accessories for Fire Alarms Systems
, UL 864, certain programming features or
options must be limited to specific values or not used at all as indicated below.
Opt # Program Option
Page
Permitted in UL 864? (Y/N)
Possible Settings
Settings Permitted (UL 864)
13-14
15-16
17
18
19
1A
1B
1C
1D
1E
1F
21
2B
TX ABSENT DEBOUNCE TIME - - - - - - - 6
TX ABSENT RESTORE TIME - - - - - - - - - 6
MASK NETWORK PRESENT - - - - - - - - - 6
MASK NETWORK ABSENT- - - - - - - - - - 6
MASK TX RESTORAL - - - - - - - - - - - - - 7
MASK TX FAILURE - - - - - - - - - - - - - - - 7
MASK TX SWAP- - - - - - - - - - - - - - - - - 7
MASK TX UNENCRYPTED - - - - - - - - - - 7
MASK INVALID REPORT - - - - - - - - - - - 7
MASK UNKNOWN ACCOUNT - - - - - - - 7
MASK ACCOUNT EXCEEDED - - - - - - - - 7
MASK OPTION CHANGE - - - - - - - - - - 7
BUSY OUT - - - - - - - - - - - - - - - - - - - - 8
N
N
N
N
N
N
N
N
N
N
N
N
N
1E - FFH (30-255)
1E - FFH (30-255)
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
00-05
05AH(90s)
05AH(90s)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
00