20
Second” message is displayed; this message will be displayed:
Year/Second:1/0
0 Change to:X
Program Option [21] as “1” to include the year in the alarm
message date; alarm messages will be printed as follows:
L01-1234-05 Alarm 21:24-24/11/97
Note that the time (21:24) is represented with just hours and
minutes, and that the year is added to the date (24/11/97).
Program Option [21] as “0” to include the seconds in the
alarm message time; alarm messages will be printed as
follows:
L01-1234-05 Alarm 21:24:30-24/11
Note that the time (21:24:30) now includes hours, minutes
and seconds; the date (24/11) only indicates the day and
the month.
NOTE:
This option will affect COM1 when COM1 is
programmed with communication format 4.
Option 22: System Reset
To reset the CPM2 program, press the [ACK] button when
the “22: Force Reset” message is displayed; this message
will be displayed:
Force Sys Reset
Ent=Yes Bsp=No
Press the [Backspace] button to cancel the option without
resetting the CPM2. To reset the CPM2, press the [Enter]
button.
The reset will take approximately 8 seconds to complete.
Press the [Backspace] or [Escape] buttons to move to the
next Configuration Option.
Option 23: Change Receiver Number
The receiver number is used to identify the receiver when
communicating to COM1 and printer to report internal troubles.
To change the receiver number, press the [ACK] button
when the “23: Chg Receiver#” message is displayed. This
message will be displayed:
Receiver Number:
01 Chg to:xx
Enter a new receiver number using the hexadecimal numbers
“01” to “FF”. When a new number is entered, press the
[Enter] button.
Note that when Option [23] is programmed, the display will
return to Option [01].
8.8 Message Priorities
When in Standby Mode, the CPM2 will display warning and
other operational messages according to the following priority:
1
UL Requirement Message
2
COM1/COM2 Diagnostics
3
Line Card Diagnostics
4
“Retain last message” displays
5
Printer Error
6
COM1 Absent
7
12V Battery Low
8
9V Battery Low
9
AC Failure
10
Standby Mode message
UL Requirement Message
When Option [12] is programmed as “01”, the “ACK” button
must be pressed to acknowledge each incoming alarm
manually and to silence the internal buzzer.
COM1 Diagnostics
If both Option [16] and Option [06] are enabled, the screen
will display the data being communicated through COM1.
Refer to Option [16] for information.
Line Card Diagnostics
If Option [18] is enabled, the screen will display that data
exchanged between the CPM2 and the selected Line Card.
Refer to Option [18] for more information.
“Retain Last Message” Displays
If Option [15] is enabled, the latest printer message will be
retained on the display screen. Refer to Option [15] for
more information.
Printer Error
If Option [04] is enabled and there is a printer trouble (for
example, printer off-line, paper out, and so on), a message
similar to this will be displayed:
*Feb-23 07:30:45
<Printer ERROR!>
COM1 Absent
If Option 06 is enabled and COM1 is absent (for example,
disconnects, off-line, or fails to sent acknowledge signal),
a message similar to this will be displayed:
*Feb-23 07:30:45
<<Com#1 ABSENT>>
12V Battery Low
If the 12V back-up battery is disconnected or its voltage is
low, a message similar to this will be displayed:
*Feb-23 07:30:45
12V Battery LOW!
AC Failure
If AC power is removed from the CPM2, this message will
be displayed:
*Feb-23 07:30:45
<AC Power LOST!>
Standby Mode Message
During normal standby operation, this message will be
displayed:
*Feb-23 07:30:45
Scanning 0E (14)
Section 8
firealarmresources.com
