©2014 Tyco Security Products, Toronto, Canada www.dsc.com Tech. Support: 1-800-
387
-3
6
3
0
lary applications in accordance with the requirements in the Stand-
ards UL 639 and ULC- S306 for Intrusion Detection Units.
For UL/ULC installations use these device only in conjunction with
compatible DSC wireless receivers: HSM2HOST9, HS2LCDRF (P)9,
HS2ICNRF(P) 9 and PG9920. After installation verify the product func-
tionality in conjunction with the compatible receiver used.
FC C C OM PLIA N C E STA TEM EN T
WARNING! Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in residential installations. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause such interference,
which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the fol-
lowing measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one
that supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
FCC ID: F5314PG9944
Indust r y C anada St at e m e nt
This equipment complies with FCC and IC RF radiation exposure lim-
its set forth for an uncontrolled environment.
This device complies with FCC Rules Part 15 and with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference that
may be received or that may cause undesired operation.
Le present appareil est conforme aux CNR d'Industrie Canada applic-
ables aux appareils radio exempts de licence. L'exploitation est
autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioelectrique subi, meme si le brouillage
est susceptible d'en compromettre le fonctionnement.
IC:160A-PG9944
Europe: The PG4944 and PG8944 are compliant
with the RTTE requirements - Directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999. The PG8944 is cer-
tified to the following standards: EN50131-2-2 GRADE 2, CLASS IV,
EN50131-6 Type C. Certification is for only the 868 MHz variant of
this product. According to EN 50131-1:2006 and A1:2009, this equip-
ment can be applied in installed systems up to and including Secur-
ity Grade 2, Environmental Class II. UK: The PG8944 is suitable for
use in systems installed to conform to PD6662:2010 at Grade 2 and
environmental class 2 BS8243. The Power G peripheral devices have
two-way communication functionality, providing additional benefits
as described in the technical brochure. This functionality has not
been tested to comply with the respective technical requirements
and should therefore be considered outside the scope of the
product’s certification.
Limited Warranty
Digital Security Controls (DSC) warrants that for a period of twelve
months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in
fulfilment of any breach of such warranty, DSC shall, at its option,
repair or replace the defective equipment upon return of the equip-
ment to its factory. This warranty applies only to defects in parts
and workmanship and not to damage incurred in shipping or hand-
ling, or damage due to causes beyond the control of DSC such as
lightning, excessive voltage, mechanical shock, water damage, or
damage arising out of abuse, alteration or improper application of
the equipment.
The foregoing warranty shall apply only to the original buyer, and
is and shall be in lieu of any and all other warranties, whether
expressed or implied and of all other obligations or liabilities on
the part of DSC. This warranty contains the entire warranty. Digital
Security Controls neither assumes responsibility for, nor authorizes
any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or
liability concerning this product. In no event shall DSC be liable for
any direct or indirect or consequential damages, loss of anticipated
profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of
this product.
Warning: Digital Security Controls recommends that the entire system
be completely tested on a regular basis. However, despite frequent
testing, and due to, but not limited to, criminal tampering or elec-
trical disruption, it is possible for this product to fail to perform as
expected.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or
without Products and Components is copyrighted and is purchased
under the following license terms:
This End-User License Agreement (“EULA”) is a legal agreement
between You (the company, individual or entity who acquired the
Software and any related Hardware) and Digital Security Controls, a
division of Tyco Safety Products Canada Ltd. (“DSC”), the man-
ufacturer of the integrated security systems and the developer of the
software and any related products or components (“HARDWARE”)
which You acquired. If the DSC software product (“SOFTWARE
PRODUCT” or “SOFTWARE”) is intended to be accompanied by
HARDWARE, and is NOT accompanied by new HARDWARE, You may not
use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT
includes computer software, and may include associated media, prin-
ted materials, and “online” or electronic documentation. Any soft-
ware provided along with the SOFTWARE PRODUCT that is associated
with a separate end- user license agreement is licensed to You under
the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise
using the SOFTWARE PRODUCT, You agree unconditionally to be
bound by the terms of this EULA, even if this EULA is deemed to be
a modification of any previous arrangement or contract. If You do not
agree to the terms of this EULA, DSC is unwilling to license the
SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and inter-
national copyright treaties, as well as other intellectual property
laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You
may have only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be
installed, accessed, displayed, run, shared or used concurrently on
or from different computers, including a workstation, terminal or
other digital electronic device (“Device”). In other words, if You
have several workstations, You will have to acquire a license for
each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE
PRODUCT, but You may only have one copy per license installed at
any given time. You may use the back-up copy solely for archival pur-
poses. Except as expressly provided in this EULA, You may not oth-
erwise make copies of the SOFTWARE PRODUCT, including the printed
materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disas-
sembly - You may not reverse engineer, decompile, or disassemble
the SOFTWARE PRODUCT, except and only to the extent that such
activity is expressly permitted by applicable law notwithstanding
this limitation. You may not make any changes or modifications to
the Software, without the written permission of an officer of DSC.
You may not remove any proprietary notices, marks or labels from
the Software Product. You shall institute reasonable measures to
ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed
as a single product. Its component parts may not be separated for
use on more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with
HARDWARE, then the SOFTWARE PRODUCT is licensed with the
HARDWARE as a single integrated product. In this case, the
SOFTWARE PRODUCT may only be used with the HARDWARE as set
forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT.
You may not make it available to others or post it on a server or
web site.
(e) Software Product Transfer - You may transfer all of Your rights
under this EULA only as part of a permanent sale or transfer of the
HARDWARE, provided You retain no copies, You transfer all of the
SOFTWARE PRODUCT (including all component parts, the media and
printed materials, any upgrades and this EULA), and provided the
recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT
is an upgrade, any transfer must also include all prior versions of
the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may ter-
minate this EULA if You fail to comply with the terms and conditions
of this EULA. In such event, You must destroy all copies of the
SOFTWARE PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in con-
nection with any trademarks or service marks of DSC or its sup-
pliers.
3. COPYRIGHT - All title and intellectual property rights in and to the
SOFTWARE PRODUCT (including but not limited to any images, pho-
tographs, and text incorporated into the SOFTWARE PRODUCT), the
accompanying printed materials, and any copies of the SOFTWARE
PRODUCT, are owned by DSC or its suppliers. You may not copy the
printed materials accompanying the SOFTWARE PRODUCT. All title and
intellectual property rights in and to the content which may be
accessed through use of the SOFTWARE PRODUCT are the property of
the respective content owner and may be protected by applicable
copyright or other intellectual property laws and treaties. This EULA
grants You no rights to use such content. All rights not expressly
granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-
export the SOFTWARE PRODUCT to any country, person, or entity sub-
ject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by
the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agree-
ment shall be determined by final and binding arbitration in accord-
ance with the Arbitration Act, and the parties agree to be bound by
the arbitrator’s decision. The place of arbitration shall be Toronto,
Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT
WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET
YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be respons-
ible for problems caused by changes in the operating characteristics
of the HARDWARE, or for problems in the interaction of the SOFTWARE
PRODUCT with non-DSC- SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF
RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR
CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE
LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL
BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU
TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS
(CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE
ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER
WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON
ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO
ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS
SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO
CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR
ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT
LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR
ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE
OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,
PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING
CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends that
the entire system be completely tested on a regular basis. However,
despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this SOFTWARE
PRODUCT to fail to perform as expected.
The term IC before the radio certification number signifies that the
Industry Canada technical specifications were met. This Class B
digital apparatus complies with Canadian ICES-003. This device
complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause inter-
ference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. Cet
appareil numérique de la classe B est conforme à la norme NMB- 003
du Canada. Ce dispositif satisfait aux exigences d’Industrie Canada,
prescrites dans le document CNR- 210. son utilisation est autorisée
seulement aux conditions suivantes: (1) il ne doit pas produire de
brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter
tout brouillage radioélectrique reçu, même si ce brouillage est sus-
ceptible de compromettre le fonctionnement du dispositif.
