DM-C and DM-W: Detector Mounting Brackets
Use the optional DM-W Wall Mount and DM-C Ceiling Mount brackets to solve difficult
placement problems. The DM-W and DM-C mount to either the wall or ceiling and
allow for full vertical and horizontal positioning of the motion detector - the detector
can be tilted up or down and rotated through 90° to obtain the best position for opti-
mal coverage.
FCC COMPLIANCE STATEMENT
CAUTION
: Changes or modifications not expressly approved by Digital Security Controls could void your author-
ity to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accor-
dance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type
tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of
Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residen-
tial installation. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to television or radio reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional sugges-
tions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve Radio/
Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washing-
ton, D.C. 20402, Stock # 004-000-00345-4.
LIMITED WARRANTY
Digital Security Controls warrants that for a period of twelve months from the date of purchase, the product shall be
free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty,
Digital Security Controls shall, at its option, repair or replace the defective equipment upon return of the equipment
to its repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in
shipping or handling, or damage due to causes beyond the control of Digital Security Controls such as lightning,
excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper applica-
tion of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warran-
ties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls.
Digital Security Controls neither assumes, nor authorizes any other person purporting to act on its behalf to modify
or to change this warranty, nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of antici-
pated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.
Motion detectors can only detect motion within the designated areas as shown in their respective installation instruc-
tions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volu-
metric area protection. They have multiple beams of detection and motion can only be detected in unobstructed
areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors,
glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as mask-
ing, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system
will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be
reduced when the ambient temperature rises near or above body temperature or if there are intentional or uninten-
tional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves,
barbeques, fireplaces, sunlight, steam vents, lighting and so on.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular
basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical dis-
ruption, it is possible for this product to fail to perform as expected.
Important Information: Changes or modifications not expressly approved by Digital Security Controls could
void the user’s authority to operate this equipment.
©2006 Digital Security Controls
Toronto, Canada •
www.dsc.com
Tech. Support: 1-800-387-3630 (Canada, U.S.) or 905-760-3036
Printed in Canada
29004860R003
