DriSteem MP Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

DriSteem MP Скачать руководство пользователя страница 19

17

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Nonpressurized steam application

INSTALLATION

Water seal

(see Note 4)

Typical evaporative

humidifier

Depending on humidification load,

interconnecting piping may be hose,

tubing, or hard pipe

Face width

Blanked-off area

Position

tubelets

perpendicular

to airflow

Insulate

tubing and

hard pipe to

reduce steam

loss

≥ 2"

(51 mm)

1½" (38 mm)

flange

AHU width

Face

height

AHU/Overall

height

¾" (DN20) pipe thread

90˚ long

sweep

or two 45˚

elbows

Notes:

1. Locate drain air gap only in spaces with adequate temperature and air movement to absorb flash steam; otherwise, condensation may form on

nearby surfaces. Refer to governing codes for drain pipe size and maximum discharge water temperature.

2.   When mounting an Ultra-sorb in a duct, headers and flanges are mounted outside the duct.
3.  Mount the Ultra-sorb Model MP vertically (for horizontal airflow only).
4.  For nonpressurized steam applications provide a 5" (130 mm) minimum water seal. See Table 6-1.
5.   100% of the airflow must pass through the Ultra-sorb, which means that any openings surrounding it must be sealed. The blanked-off area below

the Ultra-sorb provides clearance height for water seals and condensate piping connections.

6.   Condensate must be drained.
7.   Dispersion tubes are available at: 3" (76 mm), 4" (102 mm; for 2" diameter only), 6" (152 mm), 9" (228 mm), 12" (305 mm) centers.
8.    Ultra-sorb humidifiers will be assembled, crated, and shipped intact in all sizes up to 93" (2360 mm) unit height. Ultra-sorb can be shipped

unassembled, by request, requiring field assembly.

9. Sizes are 12" to 144" (305 mm to 3658 mm) x 12" to 144" (305 mm to 3658 mm) in 1" (25 mm) increments.

Each Ultra-sorb humidifier is furnished with:

1.  Type 304 stainless steel header/separator and dispersion tubes when shipped unassembled.
2.  Hardware for connection of dispersion tubes to header when shipped unassembled.
3.  Tube grommets for connection when shipped unassembled.

*For electrode type humidifiers pitch towards Ultra-sorb MP steam dispersion panel.

For other steam generators pitch towards generation possible

  • Hose: 2"/ft (15%)
    • Insulated tubing/pipe: 1/4"/ft (2%)
    • Un-insulated tubing or pipe: 1/2"/ft (4%)

OM-7840

Open drain 1" (25 mm) air gap:

(see Note 1)

FIGURE 17-1: MOUNTING ULTRA-SORB MODEL MP (NONPRESSURIZED STEAM APPLICATION SHOWN)

Condensate header

Pitch to dispersion recommended*

Hose: 2"/ft (15%)

Tubing or Pipe: 1/8"/ft (1%)

«
...
17
18
19
20
21
...
»

Содержание MP

































Отзывы:

Нет отзывов