Alignment
Paper
Hex Box™
Connector Cord
Hex Key
Wrenches
Exhaust
Duct Clamps
Screws (for
Exhaust Shroud)
Air Tube
(black)
Water Hose
(1x blue, 1x clear)
Ethernet
Cable
Operating/
Safety
Instructions
Test Material
Reusable
Tote Bag &
Straps
LASER CUTTER QUICK START GUIDE
READ THE DREMEL LC40 OPERATING/SAFETY INSTRUCTION BEFORE SETUP AND USE.
FAILURE TO COMPLY WITH THE WARNINGS AND INSTRUCTIONS MAY RESULT IN FIRE,
EQUIPMENT DAMAGE, PROPERTY DAMAGE OR PERSONAL INJURY.
LASER CUTTER
UNBOXING
Front View
Back View
Hex Box
™ Back View
KIT CONTENTS | KNOW YOUR LASER CUTTER
1. Laserhead Knob
2. Wide Angle Camera
3. Lens
4. Laserhead
5. Touchscreen
6. Pause/ Stop Button
7. Ethernet Port
8. USB Port
9. Air Inlet
10. Power Switch
11. Power Outlet
(with power cord
attached)
12. Exhaust Fan
Power Outlet
13. Exhaust Flange
14. Water Outlet
15. Water Inlet
16. Water Tank
17. Hex Box
™
Water Outlet
18. Hex Box
™
Water Inlet
7
5
6
8
2
3
4
1
9
10
11
13
15
14
4
5
4. Connect power source.
Plug the
Power Cord
into a power outlet.
5. Fill Hex Box
™
with water
• Using a funnel, add water until tank looks full.
•
Start the pump (water level in tank should
go down).
•
Fill the tank again, while pump is running,
until tank is full and no bubbles are visible
in the Laser Tube.
•
Screw on the cap.
Note:
Refer to the Laser Cutter’s LCD Screen
to check if the system has been set up properly.
The SMART Laser™ sensors will indicate a white
icon when each step has been installed correctly.
HARDWARE SET UP
1. Locate and remove zip ties.
Open lid to identify
two zip ties. Use a small pair of scissors to
carefully cut and remove each one.
2. Connect the Hex Box
™
.
• Match Water Hoses to the appropriate fitting
labels on the Laser Cutter and appropriate
fittings on the Hex Box
™
.
• Connect the Air Tube to the Laser Cutter and
the Hex Box
™
.
• Connect the Hex Box
™
Connector Cord to the
Laser Cutter and the Hex Box
™
.
• Carefully place the Honeycomb Plate on the
bottom of the Laser Cutter.
3. Connect the Exhaust Duct
•
Attach the Exhaust Shroud to the Laser Cutter
and secure with Screws.
•
Secure one end of the Exhaust Duct to the back
of the Laser Cutter with the Duct Clamp.
•
Attach the other end of the Exhaust Duct to
either a filtration system (not included), an
exhaust port, or place outside a window.
1
2
3
Create a workstation.
Carefully open the top of the box.
1. Remove Reusable Tote Bag from packing and pull out the
inside box.
Open lid to reveal the test material and the
Honeycomb Plate.
2. Remove Operating/Safety Instructions, Water Hoses, Air
Tube, Screws, Hex Box Cap, Hex Key Wrench, Spacer Puck
from the other box.
3. Remove foam to reveal the Laser Cutter. Use two people
to lift the Laser Cutter out of box by straps.
After the
Laser Cutter has been taken out of the box, hook straps to
the Reusable Tote Bag. DO NOT CUT STRAPS.
4. Open the lid of the Laser Cutter
to reveal box with
Hex Box, Exhaust Duct, & Exhaust Shroud.
5. Use two people
lift the laser cutter and place on your
workstation.
Note:
Save your Dremel DigiLab Laser Cutter packaging
for future transport and storage.
Laser Cutter
Hex Box™
Honeycomb
Plate
Quick Start
Guide
Alcohol
Wipes
Exhaust
Duct
Exhaust
Shroud
HARDWARE SET UP CONTINUED
18
17
Hex Box™ Cap
Spacer Puck
Thank you
Quick Start Guide
Thank you card
Foam
Foam
Foam
Reusable Tote Bag containing
Wood Sheet & Honeycomb Plate
Laser Cutter
Reusable strap
(DO NOT CUT STRAPS)
Operating/Safety
Instructions, Water Hoses,
Air Tube, Screws, Hex Box
Cap, Hex Key Wrench,
Spacer Puck
1
2
3
4
12
Back View
Pre-attached Power Cord
16
Front View
Back View
Back View
OPERATING/SAFETY INSTRUCTIONS
START
COOLING
STOP
AIR ASSIST
VENT FAN
LID
