background image

         http://dreamcatcher.asia/cw 

 

 

 

 

 

 

 

 

 

 

        [email protected] 

 
ME1110 Digital Modulation Technique 
 

 

Quick Start Guide - 10/16 

      

                     

                                                        

 

Step 3: 

 

Displaying the Modulated IQ Signals in the 89601 VSA Software (cont.) 

 

 In the VSA software 
window, select 

Utilities > 

Frequency Reference

Select 

Internal 

to use the 

internal clock from the 
oscilloscope.  
 

 
 
 
 
 

Select

 MeasSetup > 

Frequency. 

 Set the 

center frequency to 

10 

MHz

 and the frequency 

span to 

3 MHz

, as shown 

at the side. 

 
 
 
 
 
 
 
Select 

MeasSetup > 

Measurement Type > 
Digital Demod

 to 

demodulate the QPSK 
signal. 
 
 
 
 
 
 
 
 

Select 

MeasSetup > 

Digital Demod Properties

 

to set the demodulation 
properties. In the 

Format

 

tab, set the following 
parameters: 

Format = 

QPSK, Symbol Rate = 1 
MHz, Points/Symbol = 4, 

and

 Result Length = 80 

Symbols. 

A warning about 

insufficient data for digital 
demodulation may appear. 
Ignore this and continue 
with the setup, then click 
the 

Run

 button. 

 

 

 

 

 

 
 

 

 

1

1

1

1

1

1

Содержание ME1110

















Отзывы: