background image

 

 

To limit regulation - pull off the thermostat knob (it will be tough at first) and you will find two cylindrical pins 

Ø2,15mm on the back side of the knob 

                              - pull off one pin and insert it to the corresponding hole of the selected maximum temperature. 
                              

- put the knob back on (to the stop). 

   

 

To block the setting – set the selected temperature 

pull off the thermostat knob without changing the setting, there are two pins on the back 
side of the knob 
Pull off both of them and fit them to the holes corresponding with the selected 
temperature so that the gap between the pins was without a hole, and the position was 
opposite the set temperature. 

 

3. 

Structure of the heater

 

 

 

 

thermometer 

heating element well 

 

 

 

thermowell

 

ceramic heating element 

2000W   

 

hot water withdrawal pipe

 

operation thermostat with external control 

 

Mg anode

 

 

and safety thermostat 

 

 

 

10 

enamelled steel receptacle 

electric installation guard 

 

 

 

11 

polyurethane insulation

 

cold water filling pipe 

 

 

 

12 

heater shell

 

 
4.

 

Operating conditions 

 4.1.  General 

The tank shall only be used in accordance with the conditions specified on the performance plate and in instructions 
for electric wiring. Besides legally acknowledged national regulations and standards, also conditions for connection 
defined in local electric and water works have to be adhered to, as well as the installation and operation manual.

 

 

Regulation limited

 

To block the setting 

 

Type

OKHE 80

OKHE 100

OKHE 125

OKHE 160

A

742

887

1052

1237

B

610 (560)

700 (650)

850 (800)

1050 (1000)

C

127 (177)

182 (232)

197 (247)

182 (232)

service weight

 37 kg

42 kg

49 kg

57 kg

TAB. 2 

Содержание OKHE 100










Отзывы: