background image

17 

-

 

 

 

Both the electric and water installation must follow and meet the requirements and 

regulations relevant in the country of use! 

We emphasize that the tank shall not be connected to power supply if flammable liquids 

(benzine, stain cleaner) or gases, etc., are handled in its proximity. 

 

4.2

 

SPARE PARTS 

G ¾" safety valve is packed with the product and the OKH 100, 125, 160 NTR and OKH 100, 125 NTR/ HV 
types are additionally equipped with a discharge valve.

 

 It is in your own interest to check the completeness of the accessories.  

 

 

4.3

 

DISPOSAL OF PACKAGING MATERIAL 
AND NON-FUNCTIONING PRODUCT 

A  service  fee  for  providing  return  and  recovery  of  packaging  material  has 

been paid for the packaging in which the product was delivered.

 

The service 

fee  was  paid  pursuant

 

to Act  No 477/2001  Coll., as amended,  at  EKO

-KOM 

a.s.  The  client  number  of  the  company  is  F06020274.

 

Take  the  water  tank 

packages to a waste disposal place determined by the municipality.

 

When the 

operation  terminates,  disassemble  and  transport  the  discarded  and 

unserviceable heater to a waste recycling centre (collecting yard), or contact 

the manufacturer.

  

 

 

 

 

31

-

3

-

2016

 

 

Содержание OKH 100 NTR


















Отзывы: