Draper Silhouette/Series E Скачать руководство пользователя страница 2

220V Silhouette/Series E & V by Draper 

Page 2 of 5

Removing Case Fascia

Caution: When removing or reattaching fascia, do not handle fascia by 
unpainted ends.

Case fascia is removable to access roller assembly. To remove fascia, depress 
outward the spring lip located inside lower front corner of screen case and 
pull lower corner of fascia outward. Repeat this at right end of case. Support 
fascia from center and rotate lower front edge upward approximately 40° to 
disengage the Roll-Lok hinge at the top front of screen case. Fascia can now 
be completely removed from case.
To install fascia, generally reverse instructions above making sure the Roll-
Lok hinge is completely engaged before rotating fascia down towards the 

closed position. Depress spring clips outward, push lower corners of fascia 

inward until lips of spring clips hook behind fascia.

Please Note: Be sure the clips are completely up against 
the ends of the fascia.

Electrical Connections

Screen operates on 220V AC, 50 Hz., 1 ph current. .75 amp current draw. 
Duty Cycle: ON 28 seconds/OFF 4 minutes.
Junction box is located at left end of screen. It is accessible through front 
of screen case after fascia is removed (see instructions above for removing 
fascia). Electrical supply wires can enter through the back or top of case. For 
top entry, remove plug from top conduit hole and snap plug into hole on back 
side of case.
Junction box contains brown, black, and blue pigtail leads and green internal 
ground wire per wiring diagram attached.
If optional low voltage control or video interface control is specified and factory
installed, please refer to wiring diagram on page three.
Wall or ceiling electrical box should be installed so as to be fully concealed by 
screen case after installation.
Screen is shipped with internal wiring complete and control switch(es) fully 
boxed. Wire to connect screen to switch(es) and switch(es) to power supply 
should be furnished by installer. Connections should be made in accordance 
with attached wiring diagram, and wiring should comply with national and 
local electrical codes.

All operating switches should be “off” before power is connected.

Operation

Before operating screen, remove any shipping brackets or tape securing fabric 
and dowel to the roller. If viewing surface is hanging out of the case 20 to 23 
cm, tape has probably been broken by rough handling in shipment, allowing 
surface to “unwrap” one turn off the roller. Manually wrap fabric back around 
the roller without turning the roller itself.
When screen is first operated, 

be cautious! 

Cycle unit down and up several 

times to confirm satisfactory operation. 
 

220V SINGLE STATION CONTROL

—3-position UP-OFF-DOWN switch 

permits operation to be stopped at any point. Factory adjusted limit switches 
automatically stop screen when fully down or fully up. 
 

220V MULTIPLE STATION CONTROL

—(Not CE Approved) Switches are 

similar in appearance to 220V Single Station Control. Screen stops when 
switch is released and may be restarted in either direction. Factory adjusted 
limit switches stop screen automatically when fully down or fully up. 

24V MULTIPLE STATION CONTROL

—Three-button UP-STOP-DOWN 

switches stop at any point desired, operate in any sequence. Factory adjusted 
limit switches automatically stop screen when fully down or fully up. Installer 
should incorporate an all-pole disconnect in the fixed wiring. 

220V & 12V VIDEO INTERFACE CONTROL

—(Not CE Approved) Allows 

screen to be controlled by a trigger signal—when the signal comes on, the 
screen descends automatically. Two versions: Model VIC220 integrates screen 
operation with a Draper video projector lift or a video projector or tuner with 
a 220V switch outlet. Model VIC12 interfaces with a 12V switch outlet. Both 
available with an override switch (VIC–OS), permitting independent operation. 
VIC–OS not available with factory installed VIC220 & VIC12. 
 

KEY OPERATED SWITCHING

—(Not CE Approved) Two kinds of key-

operated switches are optionally available with this unit.

1

  The key-operated power supply switch controls power to the screen and  

  switches. When it is “off”, the switches will not operate screen. 
  Key may be removed from the switch in either “on” or “off” position.

2

  A three-position key switch permits the screen to be operated directly by  

  key. In this case, the screen’s operator must always have a key.

RS232/ETHERNET—

Serial communication and network communication 

optionally available with wall switches, RF or IR remote.

Mounting on 15 cm extension wall brackets:

 

15 cm or 25-36 cm Extension 

Wall Brackets are needed to mount Silhouette extended from wall. Wall Brack-

ets are not supplied with screen and must be ordered separately. Specify 

“Silhouette Extension Wall Brackets”.

1

  Mount the Wall Brackets to the wall, making sure they are level and verti- 

  cally plumb. Installer must insure fasteners (not included) are of adequate  

  strength and suitable for chosen mounting surface.

2

  Attach hanging bracket to wall bracket as shown. 

3

  Attach (1) “Z” Clip and (1) Support Plate (supplied with screen) to hanging  

  bracket as shown.

4

  Engage the lip on back of screen case with lip of “Z” Clip and gently pull  

  down to fully engage case to brackets. 

5

  Install hook bracket as shown making sure the two tabs of this bracket  

  hook over the case extrusion.

6

  Install #10-24 hex head screw through hook bracket, hanging bracket, and  

  support plate as shown.

www.draperinc.com

(765) 987-7999

Hook

Bracket

CB ¼"-20 x 1¾" Z Keg,

Flat Washer,

¼"-20 Nylock Nut

#10-24 x 

7

/

8

"

Phillips Pan Head

Screw, Nylock Nut

#10-24 x ½"

Hex Head Screw

Z Clip

Wall

Bracket

Support

Plate

Hanging

Bracket

Caution: Do not remove the roller assembly from the case unless neces-

sary for repairs. If the roller assembly is removed, be sure motor is fully re-

seated in the bracket. If mounting style incorporates a retaining spring (left 

below), be sure the retaining spring is reinstalled.

Отзывы: