PLEASE READ -
Safety Information
WARNING
Improper installation and use of the N C screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to
imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.
1.
Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2.
Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional.
3.
Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner’s and installer’s
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper
®
, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.
4.
It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting.
5.
All hardware must be installed level. Unit must be level and square.
6.
Never leave the area while operating the unit during installation, maintenance,
or normal operation, unless it is secure and safe.
7.
Before testing or operation, carefully inspect the entire area and path
(especially
underneath)
of unit to be sure no persons or objects are in the area.
8.
During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
9.
After installation, the entire system should be carefully tested to ensure safe
and normal operation. Extreme care should be taken during testing to remain
clear of moving parts to avoid possible injury.
10.
Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.
11.
The safety features of the unit should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.
12.
Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.
13. Failure to precisely follow installation guidelines invalidates all
warranties.
14.
Custom products/installations may not be reflected in this manual. Call Draper,
Inc., if you have questions about the installation of custom products or any
questions about your installation.
Before Beginning Installation
1.
Look for any job site conditions that could interfere with installation or
operation of the system.
2.
Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to serve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper, Inc., is
not responsible for improper installation, application, testing, or workmanship
related to the product at place of installation. Please retain all instructions for
future use.
3.
Open cartons lengthwise.
4.
Locate and lay out all pieces.
5.
Inspect all boxes to make sure you have received the proper unit and parts.
6.
If you have any difficulties with installing, servicing, or operating your unit, call
your dealer or Draper, Inc., 765-987-7999.
Important Safety Information
Important Safety Information
Section 1 -
Prepare for Installation
1.
Make sure mounting surface is strong enough to hold N.
Please Note:
Installer is responsible for selecting mounting hardware
appropriate for site conditions. Ensure that fasteners are of adequate
strength and suitable for the mounting surface chosen.
2.
Verify unit measurements, and make sure it will fit in desired location.
Please Note:
The Dowel does not retract into Case. This will need to be
accounted for if mounting over a swinging window or door.
3.
Mounting brackets MUST be installed with a gap of 1¾"
(44mm)
between
Endcap and Mounting Bracket edge
(Fig. 1)
. Mark wall, jamb, or ceiling.
4.
Drill small starter holes
(if necessary)
in mounting surface.
1¾"
(44mm)
ENDC
AP
MOUNTING
BRACKET
Figure 1
page 2 of 8
N C
