Section 5 -
Limit Switch Adjustments
Standard and Quiet Motors
Caution:
Unit ships without limits. Limits will need to be
set before the unit is operated. Always be prepared to
shut off manually when new adjustment is being tested.
Push Button Limits
1.
Fully depress both limit switch push buttons, then
operate wall switch to make sure system works
properly.
2.
Raise shade to desired "UP" stop position.
3.
Set upper limit by depressing proper
(back)
push button.
4.
Lower shade to desired "DOWN" stop position.
5.
Set lower limit by depressing proper
(front)
push
button.
Caution:
-
Be sure all switches are in
"off" position before adjusting
limit switches.
-
Shade may be damaged by
running shade fabric up too
far and exposing roller.
-
If using a group control
system, each limit switch
must be set prior to
connecting to system.
-
Motor must be installed so
limit switches are pointed up
or accessible.
Screw-Type Limits
6.
Determine which direction of fabric travel corresponds with arrows on motor.
7.
Operate shade to desired "down" stop position.
Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.
8.
Operate shade to desired "up" stopping position.
Set limit by turning proper screw toward "-" to raise limit, and "+" to lower it.
Please Note:
Each full rotation of the limit screw equals approximately
5/8
"
(16mm)
of shade travel, which may
require rotating the limit screw several times.
Caution:
DO NOT allow the hem bar to hit the upper roller or fascia. This will damage the unit.
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
PUSH BUTTON LIMITS
Standard right-hand
motor configuration shown
SCREW-TYPE LIMITS
Standard right-hand
motor configuration shown
Section 6 -
Complete Electrical Connection
Operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch
(es)
fully boxed, and supplied with a 6'
(183 cm)
cable
lead
(standard)
. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to
connect shade to switch
(es)
and switch
(es)
to power supply should be furnished by installer. Connections should be made in accordance with attached wiring
diagram, and wiring should comply with national and local electrical codes.
DO NOT wire motors in parallel without written permission from Draper.
All operating switches should be “off” before power is connected.
Controls & System Overview
Sonesse
®
RTS 120VAC Motors
B W G
RTS
MOTOR
120V
110-120V Line
Decora RTS
Wireless Keypad
Patio
RF Remote
STOP
Dashed Wiring
by Electrician
NOTE: Test shade operation
If shade direction does not
correspond with the switch
orientation, turn power back
off and switch the red and black
wires from the motor to the switch.
Do not wire motors in parallel without
written permission from Draper.
Controls & System Overview
Sonesse
®
120VAC Motors
W B R G
B
Control
Switch
Single Gang
Box (by others)
120V
MOTOR
110-120V Line
Dashed Wiring
by Electrician
Sonesse
®
is a registered trademark of Somfy
®
Systems, Inc.
Please Note:
NEMA 3 prong
plugs provided by others.
page 6 of 10
Exterior Motorized FlexShade
®
XL
