background image

CLOTH WIDTH 

POCKET HEADBOX

SHADE WIDTH

SHADE FABRIC

FASCIA

OVERALL WIDTH

Fabric Width = Overall Width - 1

(41mm)

SHADE

  HEIGHT*

*When measuring shade height, remember to include Endcaps & Fascia.

HEM BAR

   3"

(76mm)

3"

(76mm)

"

(176mm)

FASCIA

HEIGHT:

7"

(178mm)

1

"

(43mm)

5

"

(146mm)

1

"

(46mm)

3

"

(81mm)

6

"

(167mm)

7

"

(197mm)

1

"

(32mm)

2

"

(60mm)

"

(1.6mm)

"

(16mm)

"

(14mm)

  1

 (38mm)

"

(22mm)

"

(17mm)

"

(17mm)

4

"

(121mm)

"

(19mm)

"

(2.4mm)

 7

"

(197mm)

Inside Width = Overall Housing Cut - Length =  Shade 

(4.8mm)

Standard Dual Roller Clutch - 

Operated Endcap & Fascia Dimensions

Standard Dual Roller Clutch - 

Operated Pocket Headbox Dimensions

Section 6 -

 Bead Chain Limits and Safety Device Installation

Attaching Stop Balls

1. 

Set upper and lower travel limits by installing stop balls to bead chain 

(crimp closed using pliers)

 

(Fig. 6-A)

.

P-Clip Cord Tension Device

Please Note:

 Draper

®

 Bead Chain Clutch-Operated shades that do not comply with WMCA/ANSI Standard A100.1-2012 

come with a P-Clip cord tension device pre-attached to bead chain 

(Fig. 7-B)

. This device must be attached to wall, 

jamb, or sill so that bead chain is held taut enough that children cannot pull it away from wall or fit their head into loop.

Spring-Loaded Cord Tension Device

If Draper

®

 Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded Cord Tension Device 

comes installed on bead chain 

(Fig. 6-C)

. An approved permanent warning label and approved mechanical fasteners 

(wood 

screws)

 are included. Device is designed so that children cannot pull bead chain away from wall or fit their head into loop. 

(See safety note on page 2)

. For more information, visi

www.draperinc.com/windowshades/wcmacompliance.aspx

.

1. 

Install cord tension device to wall, jamb, or sill. 

2. 

Pull tensioner down so that bead chain is held taut and use mounting hardware to keep it taut. 

Please Note:

 Bead chain should be taut enough to move smoothly through device. However, overtightening screws will 

damage Spring-Loaded Tension Device.

Chain Limits

Chain Tension Device

Figure 6-A

1. Attach 

    stop balls.

2. Crimp 

    closed

    with 

    pliers.

Sill

Mount

Jamb

Mount

Tensioner

P-Clip

Figure 6-B

P-Clip

Figure 6-C

page 8 of 8

Dual Roller Clutch-Operated FlexShade

®

Section 7 -

 Dimensions

Содержание Clutch-Operated FlexShade









Отзывы: