manualshive.com logo in svg

Draper 67089, Руководство пользователя

Поделиться
Скачать
Draper 67089 Скачать руководство пользователя страница 15

Tool will not shut off.

–  Throttle valve ‘O’ ring broken or 

unseated.

–  Throttle valve stem bent or 

jammed with dirt particles.

–  Replace new ‘O’ rings.
–  Lubricate trigger with air tool 

lubricating oil. If trigger remains 
jammed return to service centre.

Tool runs at normal speed but loses 
power under load.

–  Motor parts worn.
–  Cam clutch worn or sticking due 

to lack of lubricant.

–  Lubricant clutch housing.
–  Check for excess clutch oil. 

Clutch cases need only be half 
full. Overfilling can cause drag 
on high speed clutch parts. A 
typical oil, lubricated wrench only 
requires 1/2 ounce of clutch oil.

Grease Lubricated: Note:

Heat usually indicates insufficient 
grease in chamber. Severe 
operating conditions may require 
more frequent lubrication.

Drive shank wear.

–  Worn sockets or using 

conventional chrome plated 
sockets.

–  For any air tools, do not use 

chrome plated conventional 
sockets under any 
circumstances as this is a highly 
dangerous practice. Use only 
high quality impact sockets as 
listed in the Draper Catalogue. 
Chrome plated sockets can 
shatter and cause injury.

Sockets will not stay on.

–  Worn anvil ring.

–  Replace anvil ring.

Motor will not run. Exhaust air flows 
freely.

–  One or more motor vanes stuck 

due to material build up.

–  Motor seized due to rust.

–  Pour air tool lubricating oil into 

air inlet.

–  Operate tool in short bursts of 

forward and/or reverse rotation 
(where applicable).

–  Tap motor housing gently with 

plastic mallet.

–  Disconnect supply, free motor by 

rotating drive shank manually.

–  If tool remains jammed, return to 

service centre.

Tool runs slowly. Air flows slightly 
from exhaust.

–  Motor parts jammed with dirt 

particles.

–  Power regulator in closed 

position.

–  Air flow blocked by dirt.

–  Check air inlet filter for blockage.
–  Pour air tool lubricating oil into 

air inlet as per instructions.

–  Operate tool in short bursts, 

quickly reversing rotation back 
and forth.

Problems

Possible cause

Required action

We recommend the 
use of Draper Air 
Tool Oil:

500ml 

Stock No.34681

1Litre 

Stock No.34682

250ml 

Stock No.34679

11.1 TROUBLESHOOTING  GUIDE

11. TROUBLESHOOTING

- 15 -

Содержание 67089



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды