Draper 20529, Инструкция по эксплуатации

Страница: 6 / 20

5. HEALTH & SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
When using any type of power tool there are steps that should be taken to make sure that you, as the user,
remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
Read the instruction manual fully.
Do not attempt any operation until you have read and understood this
manual.
Most important you must know how to safely start and stop this machine, especially in an emergency.
Keep the work area tidy and clean.
Attempting to clear clutter from around the machine during use will
reduce your concentration. Mess on the fl oor creates a trip hazard. Any liquid spilt on the fl oor could result in
you slipping.
Find a suitable location.
If the machine is bench mounted; the location should provide good natural light or
arti fi cial lighting as a replacement. Avoid damp and dust locations as it will have a negative effect on the
machine’s performance.
If the machine is portable; do not expose the tool to rain. In all cases do not operate power tools near any
fl ammable materials.
Beware of electric shock.
Avoid contact with earthed surfaces; because they can conduct electricity if there
is an electrical fault with the power tool. Always protect the power cable and route it away from danger.
Keep bystanders away.
Children, onlookers and passers by must be restricted from entering the work area
for their own protection. The barrier must extend a suitable distance from the tool user.
Unplug and house all power tools that are not in use.
A power tool should never be left unattended while
connected to the power supply. They must be housed in a suitable location, away locked up and from
children.
Do not overload or misuse the tool.
All tools are designed for a purpose and are limited to what they are
capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an application it is not
designed for. Select a tool appropriate for the size of the job. Overloading a tool will result in tool failure and
user injury: This covers the use of accessories.
Dress properly.
Loose clothing, long hair and jewellery are all dangerous because they can become
entangled in moving machinery: This can also result in parts of body being pulled into the machine.
Clothing should be close
fi tted, with any long hair tired back and jewellery and neck ties removed. Footwear
must be fully enclosed and have a nonslip sole.
Wear personal protective equipment (PPE).
Dust, noise, vibration and
swarf
can all be dangerous if not
suitably protected against. If the work involving the power tool creates dust or fumes; wear a dust mask.
Vibration to the hand, caused by operating some tools for longer periods must be protected against. Wear
vibration reducing gloves and allow long breaks between uses. Protect against dust and
swarf
by wearing
approved safety goggles or a face shield. These are some of the more common hazards and preventions;
however, always fi nd out what hazards are associated with the machine/work process and wear the most
suitable protective equipment available.
Do not breathe contaminated air.
If the work creates dust or fumes; connect the machine (if possible) to an
extraction system either locally or remotely. Working outdoors can also help if possible.
Move the machine as instructed.
If the machine is hand held, do not carry it by the power supply cable. If
the product is heavy; employ a second or third person to help move it safely or use a mechanical device.
Always refer to the instructions for the correct method.
Do not overreach.
Extending your body too far can result in a loss of balance and you falling. This could be
from a height or onto a machine and will result in injury.
Maintain your tools correctly.
A well maintained tool will do the job safely. Replace any damaged or
missing parts immediately with original parts from the manufacturer. As applicable; keep blades sharp;
moving parts clean, oiled or greased; handles clean; and emergency devices working.
Wait for the machine to stop.
Unless the machine is fi tted with a safety brake; some parts may continue to
move due to momentum. Wait for all parts to stop; then unplug it from the power supply before making any
adjustments, carrying out maintenance operations or just fi nishing using the tool.
6