background image

– 2 –

If the tool is not covered by the terms of this warranty, repairs and 

carriage charges will be quoted and charged accordingly.

This warranty supersedes any other guarantees expressed or implied and 

variations of its terms are not authorised.

Your Draper Tools guarantee is not effective until you can produce, upon 

request, a dated receipt or invoice to verify your purchase within the 

guarantee period.

Please note that this warranty is an additional benefit and does not affect 

your statutory rights.

Draper Tools Limited

3.  Specification

Stock No.

13818

Part No.

501G

Wood Test

Compound wood, thickness 10mm.

Metal Test

Diameter 20mm, Iron pipe

(depth 25mm max.)

AC Voltage test.

AC 220V Electric wire, 

(depth 25mm max.)

Ambient condition.

-20°C to 60°C below 80% RH

Battery

9V, PP3

4.  Product Identification

4.1 Product Overview

(1) 

Stud detection face

(2) 

Voltage/metal detection face

(3) 

Stud indicator (red)

(4) 

Stud indicator (green)

(5) 

Stud sensitivity dial

(6) 

Selector switch

(7) 

Voltage/metal sensitivity dial

(10)

(3)
(4)

(5)

(6)

(7)

(8)

(9)

(11)

(12)

(13)

(14)

(1)

(2)

(8) 

Power indicator (green)

(9) 

Voltage/metal indicator (red)

(10) 

Battery compartment cover

(11) 

Stud detector trimmer

(12) 

Voltage/metal detector trimmer

(13) Buzzer
(14) 

AC voltage detection adjuster 

(Factory adjustment only; 

DO NOT tamper with this setting)

5.  Health and Safety Information

• Read this manual in full before using this product.

• This device is intended for use as a guide 

ONLY.

−   Lack of response from the detector does not guarantee the 

absence of metal, currents or wall studs.

−   Caution must still be exercised when working in walls and other 

blind surfaces.

•  

DO NOT immerse this device in water or allow the battery to come 

into contact with liquids.

•  

DO NOT abuse, mutilate or burn the battery.

•   Check the device carefully before use.

−  

DO NOT use this product if it is damaged in any way or there is 

evidence of battery leakage.

WARNING! This device emits a loud audible tone. Placing your ear over 

the buzzer openings may cause hearing damage.

6.  Operation and Use

Install a 9V PP3 battery (supplied) before use; see 

7.2 Replacing the 

Battery.

6.1 AC Voltage and Metal Detection

1.  Hold the unit and rotate the voltage/metal sensitivity dial (7) fully 

downwards.

1 

Fig.

2.  Move the selector switch (6) to the 

AC Voltage/Metal Detector 

position; the power indicator (8) should illuminate.

 

Important: Ensure that the device is not positioned near any metal 

objects or current-carrying conductors when you switch it on.

3.  Rotate the sensitivity dial (7) upwards until the metal/voltage 

indicator illuminates and the audible tone sounds, then reverse the 

dial gently until the indicators switch off.

4.  Hold the device so that the voltage detection face (2) is flush with the 

wall and move it sideways across the surface.

(7)

(8)

Содержание 13818-501G







Отзывы: