manualshive.com logo in svg

Dräger Evita V300, Дополнение к инструкции по применению

Поделиться
Скачать
Dräger Evita V300 Скачать руководство пользователя страница 24

Alarm – Cause – Remedy

24

!

201

Battery activated

The ventilation unit is 
powered by the battery as 
there is no mains power 
supply.
– If PS500 is not con-

nected, the maximum 
operating time is 
30 minutes.

– If PS500 is connected, 

the maximum operating 
time is 360 minutes.

Connect device to the 
mains power supply.

!

127

Battery  charging  deferred

Battery charging is deferred 
to prevent battery 
overheating. The device 
can be used normally.

Battery charging continues 
automatically and is 
indicated by a flashing 
segment in the battery 
symbol.

!!!

254

Battery discharged

The remaining operating 
time of the battery is less 
than 5 minutes.

Connect device 
immediately to the mains 
power supply.

!!!

250

Battery low

The battery is almost 
discharged.

Connect device to the 
mains power supply.

!!

251

Battery low

The battery is almost 
discharged.

Connect device to the 
mains power supply.

!

100

Continuous nebulization 
activated

Continuous nebulization 
was activated by the user.

To end continuous 
nebulization, press the 
"Cancel" button if required.

!!!

253

Device failure

A system failure was 
detected.

Disconnect patient from the 
device and continue 
ventilation without delay 
using another independent 
ventilator.

Call DrägerService.

!!!

253

Device failure (10)

A failure was detected by 
the safety software system.

Disconnect patient from the 
device and continue 
ventilation without delay 
using another independent 
ventilator.

Call DrägerService.

Alarm 
priority

Alarm message

Cause

Remedy

Содержание Evita V300











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды