WIL-11520-E-07
1
WILDEN PUMP & ENGINEERING, LLC
CAUTION: Do not apply compressed air to the
exhaust port — pump will not function.
CAUTION: Do not over-lubricate air supply —
excess lubrication will reduce pump performance.
Pump is pre-lubed.
TEMPERATURE LIMITS:
Acetal
–29°C to 82°C –20°F to 180°F
Buna-N
–12°C to 82°C
10°F to 180°F
Geolast
®
–40°C to 82°C –40°F to 180°F
Neoprene
–18°C to 93°C
0°F to 200°F
Nordel
®
EPDM
–51°C to 138°C –60°F to 280°F
Nylon
–18°C to 93°C
0°F to 200°F
PFA
–7°C to 107°C 45°F to 225°F
Polypropylene
0°C to 79°C
32°F to 175°F
Polyurethane
–12°C to 66°C
10°F to 150°F
PVDF
–12°C to 107°C 10°F to 225°F
Saniflex™
–29°C to 104°C –20°F to 220°F
SIPD PTFE with EPDM-backed
4°C to 137°C 40°F to 280°F
SIPD PTFE with Neoprene-backed 4°C to 93°C
40°F to 200°F
PTFE
1
4°C to 104°C 40°F to 220°F
Viton
®
FKM
–40°C to 177°C –40°F to 350°F
Wil-Flex™
–40°C to 107°C –40°F to 225°F
NOTE:
Not all materials are available for all models.
Refer to Section 2 for material options for your pump.
CAUTION: When choosing pump materials, be
sure to check the temperature limits for all wetted
components. Example: Viton
®
has a maximum
limit of 177°C (350°F) but polypropylene has a
maximum limit of only 79°C (175°F).
CAUTION: Maximum temperature limits are
based upon mechanical stress only. Certain
chemicals will significantly reduce maximum
safe operating temperatures. Please consult the
Wilden Chemical Resistance Guide.
WARNING: Prevent static sparking. If static
sparking occurs, fire or explosion could result.
Pump, valves and containers must be grounded
to a proper grounding point when handling
flammable fluids and whenever discharge of
static electricity is a hazard.
CAUTION: Do not exceed 8.6 bar (125 psig) air
supply pressure.
CAUTION: The process fluid and cleaning fluids
must be chemically compatible with all wetted
pump components. Please consult the Wilden
Chemical Resistance Guide.
1
4°C to 149°C (40°F to 300°F) - 13 mm (1/2") and 25 mm (1") models only.
CAUTION: Do not exceed 82°C (180°F) air inlet
temperature for Pro-Flo
®
SHIFT models.
CAUTION: Pumps should be thoroughly flushed
before installing into process lines. FDA- and
USDA-approved pumps should be cleaned and/
or sanitized before being used.
CAUTION: Always wear safety glasses when
operating pump. If diaphragm rupture occurs,
material being pumped may be forced out air
exhaust.
CAUTION: Before any maintenance or repair is
attempted, the compressed air line to the pump
should be disconnected and all air pressure
allowed to bleed from pump. Disconnect all
intake, discharge and air lines. Drain the pump
by turning it upside down and allowing any fluid
to flow into a suitable container.
CAUTION: Blow out air line for 10 to 20 seconds
before attaching to pump to make sure all pipeline
debris is clear. Use an in-line air filter. A 5μ
(micron) air filter is recommended.
NOTE: When installing PTFE diaphragms, it is
important to tighten outer pistons simultaneously
(turning in opposite directions) to ensure tight fit.
(See torque specifications in Section 7.)
NOTE: Some PTFE-fitted pumps come standard
from the factory with expanded PTFE gaskets
installed in the diaphragm bead of the liquid
chamber. PTFE gaskets cannot be re-used.
NOTE: Before starting disassembly, mark a line
from each liquid chamber to its corresponding air
chamber. This line will assist in proper alignment
during reassembly.
CAUTION: Pro-Flo
®
pumps cannot be used
in submersible applications. Pro-Flo
®
SHIFT
pumps do have a single-point exhaust option
for submersible applications. Do not use
standard Pro-Flo
®
SHIFT models in submersible
applications.
CAUTION: Tighten all hardware prior to installation.
S e c t i o n 1
C A U T I O N S — R E A D F I R S T !
Содержание PSG Wilden PS1520
Страница 29: ...N O T E S ...
Страница 30: ...N O T E S ...