manualshive.com logo in svg

Dover PSG Wilden Pro-Flo P800 Series, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Dover PSG Wilden Pro-Flo P800 Series Скачать руководство пользователя страница 18

 

WIL-11251-E-03  

18 

P800 Bolted Plastic 

AIR VALVE DISASSEMBLY

 

Tools Required: 

 

3/16

" 

Allen Wrench 

 

 

Snap-Ring Pliers

 

 

O-Ring Pick

 

CAUTION:

 Before attempting any maintenance or repair, disconnect the compressed 

air line to the pump and allow all air pressure to bleed from the pump. Disconnect all 
intake, discharge, and air lines. Drain the pump by turning it upside down and allowing 
any fluid to flow into a suitable container. Be aware of any hazardous effects of contact 
with your process fluid. 
 

 

NOTE:

 Replace worn parts with genuine Wilden parts for reliable performance. 

 

 

 

 

 

 

 

Step 1 

  Step 2 

  Step 3 

Loosen the air valve bolts utilizing a 5 mm 
(3/16") Allen wrench. 

  Remove muffler plate and air valve bolts 

from air valve assembly exposing muffler 
gasket for inspection. Replace if 
necessary. 

  Lift away air valve assembly and remove 

air valve gasket for inspection. Replace if 
necessary. 

 
 
 
 
 
 

 

 

 

 

 

DISASSEMBLY / REASSEMBLY 

Содержание PSG Wilden Pro-Flo P800 Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды