manualshive.com logo in svg

Dover PSG Wilden PRO-FLO P1500, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Dover PSG Wilden PRO-FLO P1500 Скачать руководство пользователя страница 18

 

WIL-11160-E-10  

18 

P1500 Bolted Plastic 

 

REASSEMBLY HINTS AND TIPS

 

Upon performing applicable maintenance to the air distribution system, 
the pump can now be reassembled. Please refer to the disassembly 
instructions for photos and parts placement. 
 
To reassemble the pump, follow the disassembly instructions in 
reverse order. The air distribution system needs to be assembled first 
then the diaphragms and finally the wetted path. The applicable torque 
specifications are on this page. 
 
The following tips will assist in the assembly process: 

 

Lubricate air valve bore, center section shaft and pilot spool 

bore with NLGI grade 2 white EP bearing grease or 
equivalent. 

 

Clean the inside of the center section shaft bore to ensure 

no damage is done to new seals. 

 

A small amount of NLGI grade 2 white EP bearing grease 

can be applied to the muffler and air valve gaskets to locate 
gaskets during assembly. 

 

Make sure that the exhaust port on the muffler plate is 

centered between the two exhaust ports on the center 
section. 

 

Stainless bolts should be lubed to reduce the possibility of 
seizing during tightening. 
 

Maximum Torque Specifications

 

Description Torque 

Air Valve 

8.5 N•m (75 in-lb) 

Outer Piston 

136 N•m (100 ft-lb) 

Air Chamber/Center Block 

4.6 N•m (55 ft-lb) 

Tee Section/Elbow 

3.4 N•m (32 ft-lb) 

Elbow/Liquid Chamber 

3.4 N•m (32 ft-lb) 

Liquid Chamber/Air Chamber 

3.4 N•m (32 ft-lb) 

Diaphragm Ring and Outer Piston Assembly 

18.9 N•m (14 ft-lb) 

 

 

 

 

 

DISASSEMBLY / REASSEMBLY 

Содержание PSG Wilden PRO-FLO P1500

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды