Dover PSG Wilden P4 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

Dover PSG Wilden P4 Скачать руководство пользователя страница 5

WIL-10160-E-11

5

P4 Clamped Plastic

SECTION 2

MATERIAL CODES

MODEL

P4 = PRO-FLO

®

WETTED PATH

K = PVDF
P = POLYPROPLYENE

OUTER PISTON

K = PVDF
P = POLYPROPLYENE

AIR CHAMBER/
CENTER SECTION

A = ALUMINUM
C = PTFE-COATED ALUMINUM
L = ACETAL
S = STAINLESS STEEL
V = HALAR

®

-COATED ALUMINUM

AIR VALVE

L = ACETAL
P = POLYPROPYLENE

DIAPHRAGMS

BNS = BUNA-N (RED DOT)
BNU = BUNA-N, ULTRA-FLEX™
          (RED DOT)
EPS = EPDM (BLUE DOT)
EPU = EPDM, ULTRA-FLEX™
        (BLUE DOT)
NES = NEOPRENE (GREEN DOT)
NEU = NEOPRENE, ULTRA-FLEX™
        (GREEN DOT)
SSL = FULL-STROKE SANIFLEX™
        IPD [HYTREL

®

(CREAM)]

TEU = PTFE W/EPDM
        BACK-UP (WHITE)
TSS = FULL-STROKE PTFE
        W/SANIFLEX™ BACKUP
TSU = PTFE W/SANIFLEX™
        BACKUP (WHITE)
TWS = FULL-STROKE PTFE
        W/WIL-FLEX™ BACKUP
VTS = FKM (WHITE DOT)
VTU = FKM, ULTRA-FLEX™
ZPS = POLYURATHANE, EZ-INSTALL
ZSS = SANIFLEX™, EZ-INSTALL [HYTREL

®

]

ZWS = WIL-FLEX™ , EZ-INSTALL [SANTOPRENE

®

]

VALVE BALLS

BN = BUNA-N (RED DOT)
EP = EPDM (BLUE DOT)
FS = SANIFLEX™
[HYTREL

®

(CREAM)]

FV = SANITARY FKM
(TWO WHITE DOTS)
NE = NEOPRENE (GREEN DOT)
PU = POLYURETHANE (BROWN)
TF = PTFE (WHITE)
VT = FKM (WHITE DOT)
WF = WIL-FLEX™ [SANTOPRENE

®

(THREE BLACK DOTS)]

VALVE SEATS

K = PVDF
P = POLYPROPYLENE

T = PFA

O-RINGS

BN = BUNA-N (RED DOT)
PU = POLYURETHANE (BROWN)
TV = PTFE ENCAP. FKM

SPECIALTY CODES

0100

Wil-Gard II™ 110V

0102

Wil-Gard II™ sensor wires ONLY

0103

Wil-Gard II™ 220V

0206 PFA-coated

hardware,

Wil-Gard II™ sensor wires ONLY

0502 PFA-coated

hardware

0504 DIN

flange

0506

DIN flange, PFA-coated hardware

0512

Adapter block, no muffler,Pro-Flo®,

center

section

0513

SS outer pistons

0560 Split

manifold

0561

Split manifold, PFA-coated hardware

0563

Split manifold, discharge ONLY

0564

Split manifold, inlet ONLY

0603

PFA-coated hardware, Wil-Gard II™ 110V

0604

DIN flange, Wil-Gard II™ 220V

0606

DIN flange, PFA-coated hardware,

Wil-Gard II™ 220V

0608

PFA-coated hardware, Wil-Gard II™ 220V

0612 Ultrapure,

PFA-coated

hardware,

male

connections

0618 Ultrapure,

PFA-coated

hardware,

Wil-Gard II™ 110V, male connections

0622

Ultrapure, male connections

0624

Ultrapure, Wil-Gard II™ 110V, male connections

0660

Split manifold, Wil-Gard II™ 110V

0661

Split manifold PFA-coated hardware,

Wil-Gard II™ 110V

NOTE:

Most elastomeric materials use colored dots for identification.

NOTE:

Not all models are available with all material options

P4 PLASTIC

LEGEND P4 / X X X X X / X X X / X X / X X X / X X X X

38 mm (1-1/2") Pump
Maximum Flow Rate:
140 lpm (37 gpm)

O-RING

MODEL VALVE

SEAT SPECIALTY

VALVE

BALL

CODE

DIAPHRAGMS

AIR

VALVE

CENTER

BLOCK

AIR

CHAMBERS

OUTER PISTON

WETTED PATHS

WILDEN PUMP DESIGNATION SYSTEM

(if applicable)

«
...
3
4
5
6
7
...
»

Содержание PSG Wilden P4





























Отзывы:

Нет отзывов