Dover PSG Wilden P4 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Dover PSG Wilden P4 Скачать руководство пользователя страница 3

WIL-10160-E-11

3

P4 Clamped Plastic

CONTENTS

SECTION 1: Precautions – Read First!

.....................................................................................................

4

SECTION 2: Wilden Pump Designation System

......................................................................................

5

SECTION 3: How It Works

..........................................................................................................................

6

SECTION 4: Dimensional Drawings

..........................................................................................................

7

SECTION 5: Performance

...........................................................................................................................

8

P4 Plastic Rubber-Fitted ........................................................................................................................... 8

P4 Plastic TPE-Fitted ................................................................................................................................ 8

P4 Plastic Reduced-Stroke PTFE-Fitted ................................................................................................... 9

P4 Plastic Full-Stroke PTFE-Fitted ........................................................................................................... 9

Suction Lift Capability .............................................................................................................................. 10

SECTION 6: Suggested Installation, Operation, Maintenance, and Troubleshooting

.......................

11

SECTION 7: Disassembly/Reassembly

...................................................................................................

14

Pump Disassembly ................................................................................................................................. 14

Air Valve Disassembly ............................................................................................................................ 17

Reassembly Hints and Tips .................................................................................................................... 20

Gasket Kit Installation ............................................................................................................................. 22

SECTION 8: Exploded View and Parts List

.............................................................................................

23

SECTION 9: Elastomer Options

...............................................................................................................

27

«
1
2
3
4
5
...
»

Содержание PSG Wilden P4





























Отзывы:

Нет отзывов