manualshive.com logo in svg

Dover PSG Mouvex P BI Series, Установка - Использование - Обслуживание, Страница: 40 / 45

Поделиться
Скачать
Dover PSG Mouvex P BI Series Скачать руководство пользователя страница 40

Remounting :

• Check the condition of the contact surfaces of the

counterparts 

604

and rotating parts 

697

.

• Check the ring seals 

602

(2) - 

605

(2) - 

613

(2) and

change them as necessary.

• Check the lip seals 

707

(1) - 

716

(1) and replace if neces-

sary.

• Use a clean cloth to clean the contact surfaces of the

shaft seal.

• Mount the counterpart 

604

with its ring seal 

605

into

the insert 

603

engaging the pin 

627

in the slot in the

counterpart.

• Lubricate the shaft 

501

lightly.

• Fit the insert 

603

and seal 

602

inside the front cover

401a

. Be sure to index the insert 

603

and pin 

608

.

• Place the first rotating part 

697

and seal 

613

in posi-

tion. Keep it on the side indicated in the table and tigh-
ten the screws 

617

to keep it on the shaft 

501

.

• Place the second rotating part 

697

and seal 

613

in

position. Keep it on the side indicated and tighten the
screws 

617

to keep it on the shaft 

501

(lock the screws

with Loctite

®

643* or equivalent).

• Mount the second counterpart 

604

with its ring seal 

605

in the shaft seal holder 

601,

fitting the dowel pin 

627

into

the notch in the counterpart.

• Insert the shaft seal holder 

601

and seal 

602

in the

strainer 

725

(be careful not to bump the edge of the

counterpart 

604

of the shaft seal).

• Tighten the 2 screws 

729

and their nuts 

730

.

• Slide the strainer 

725

onto the shaft 

501

until it

contacts the front cover 

401a

.

• Tighten the 3 screws 

726

.

• Position the washer 

731

against the shoulder of the

shaft 

501

.

• Fit the bearing 

703

on the shaft by hand.

• Push it using a sleeve until it comes up against the

washer 

731

. In no case must the bearing be pushed

onto the shaft without support for the shaft 

501

.

FAILURE TO FOLLOW THIS INSTRUCTION CAN CAUSE
SERIOUS DAMAGE TO THE INTERIOR OF THE PUMP.

• Position the second washer 

731

against the bearing 

703

.

• Fit the circlip 

537

.

• Wipe the faces of the cover 

705

and strainer 

725

with

a clean cloth.

• Fit the lip seal 

707

into the cover 

705

.

• Fit the cover 

705

to the strainer 

725

.

• Tighten the 4 screws 

723

.

• Check that the pump rotates freely when turned by

hand.

• Reinstall the pump.

• Refit the retaining screws on the pump.

• Couple the pump by refitting the coupling sleeve.

• Check the pump alignment (see § ALIGNMENT OF

MOTOR/PUMP AND REDUCTION GEARBOX/PUMP
SHAFTS).

40/45

NT 1008-D00 08 18 P BI series  e

9. SHAFT SEAL (continued)

* Loctite

®

is a registered brand.

Содержание PSG Mouvex P BI Series














































Отзывы:

Нет отзывов